Friday, September 29, 2023
HomeStartWhirlpool Dishwasher Troubleshooting Not Starting

Whirlpool Dishwasher Troubleshooting Not Starting

How Do I Reset My Dishwasher

Dishwasher Wont Start Dishwasher Troubleshooting

When all else fails, you can try to reset the dishwasher. In some instances, simply resetting the dishwasher can be enough to get the job done. Just make sure that the dishwasher control panel is disconnected from the local power source for about a minute.

1. Unplug and plug back in. If the dishwasher is plugged into a local outlet, just unplug it for that minute before plugging it back in.

2. If hardwired Should it be hardwired, kill the breaker to that outlet at the main electrical panel for that same minute before turning it back on.

This should work to reset the dishwasher controls, hopefully setting it back to standard settings so that you can operate it once again.

A Faulty Circulation Pump

To determine if the wash motor is the culprit, pull your dishwasher out of its countertop compartment and listen for clicking sounds in the area behind the lower kick plate/access panel. If you hear such sounds, you can almost be sure that the motor is the problem and needs replacement.

You can either call an expert to repair or do it yourself. Should you choose the DIY route, heres a video to guide you:

How Can I Fix My Whirlpool Dishwasher When Its Not Draining

It can be very frustrating to open up your dishwasher after running it and find it didnt drain properly. A few different situations can cause the dishwasher to have an incomplete drain cycle. Lets explore each potential scenario so you can examine your appliance and try to discover the source of the problem.

You May Like: How To Reset Kitchen Aid Dishwasher

Check The Electronic Control Board

The electronic control board may be busted , causing the dishwasher not to turn on.

Follow the procedure below to troubleshoot the main control board:

  • Double check that all connections on your applianceâs control board are properly connected and tightly plugged.
  • Check the board for trouble signs . If you have seen any damage, probably that is where the problem is coming from.

Consider replacing the control board if you still cannot get the dishwasher to run .

Will My Dishwasher Turn On If The Door Is Open

Whirlpool washer error code F3 E1

With an open door, the dishwasher will not start. This safety feature ensures that the wash and dry cycles only run when the dishwasher door is closed. Remember, even if you close the door but dont latch it properly, you will have issues running the washing cycle. In such a case, pressing the start button may turn the appliance on, but it will not run complete dishwasher cycles.

Recommended Reading: Dishwasher That Hooks Up To Sink

Why Is My Dishwasher Not Starting When I Press The Start Button

I have a Whirlpool Dishwasher that’s a few years old. The blue light on the start button no longer goes on , but the dishwasher has been working fine for at least a year without the light working. Now I can’t get the dishwasher to start when I press the START button. Interestingly, I can get it to start by pressing “Heated Dry,””Normal,””Heated Dry,””Normal” and then closing the door. I think this resets the dishwasher and it cleans normally. Just pressing START on the dishwasher doesn’t seem to work, though.

I have two questions

1-How can I fix this? What is the likely problem?

2-Is it bad for the dishwasher to be starting it by pressing “Heated Dry,””Normal,””Heated Dry,””Normal”? I have done this a few times already, but don’t want to break the dishwasher. Thanks for your help!!

Ii Malfunctioning Electric Control Or Timer

If the door latch assembly is not the guilty party, you might want to check the electric timer control. This component is linked to the control panel and decides the duration of the wash cycle. If the electric control has gone kaput, the timer wont receive the power needed to start the cycle, which can prevent your appliance from turning on. The same goes if there is an improper connection between the timer and the control panel.

How to test the electric control:

  • Unplug your dishwasher.
  • Locate and remove the timer from your appliance. As previously mentioned, it is usually found in the control panel.
  • If your timer has several contacts, make sure to refer to your models wiring diagram. This will give you an idea of which wires or contacts you have to test.
  • Ready your multimeter by setting it to the Rx1000 setting. Connect to probes with the relevant contacts. Dishwasher timers typically measure anywhere from 2000 and 3500 ohms of resistance, although it may still vary from one make to another. Again, consult your owners manual to be sure.
  • If the reading that you get falls outside of the recommended range, you will have to get a replacement electric control timer.
  • Also Check: Does Lowe’s Install Dishwashers

    Examine The Dishwasher And Garbage Disposal Connection

    Because the dishwasher connects directly to the garbage disposal, youll need to ensure the two systems are connected correctly. One of the most common problems in this area is forgetting to remove the knock-out plug. You’ll find this plug near where the dishwasher drain hose attaches to the disposal. If this plug isnt removed, the water wont drain out of the dishwasher.

    Dishwasher Wont Start Troubleshoot In 9 Steps

    Dishwasher Repair & Diagnostic – Not Starting – Kitchenaid, Whirlpool, Maytag, Sears KUDS30IXBT1

    If your dishwasher wont start, save time and money by troubleshooting it before calling a professional. Repairing a dishwasher isnt as difficult as it might seem and can be done even if you arent particularly handy. Use this guide to help you troubleshoot major parts of a dishwasher and determine when professional help is necessary.

    Don’t Miss: Replace Kitchenaid Dishwasher Soap Dispenser

    Whirlpool Dishwasher Not Starting/finishing Cycle

    Categories Dishwasher, Home and Kitchen, Whirlpool Dishwasher

    Whirlpool is one of the most reliable, pocket-friendly dishwasher brands on the market. Nevertheless, its appliances arent immune to some of the common issues users typically experience with dishwashers: not starting/finishing a cycle. If youve experienced this problem or anything related, this is a post you dont want to miss.

    A Whirlpool dishwasher may not start/complete a cycle due to easy-to-fix issues like lack of water supply and enabled control lock/sleep mode, and overloading. Other times, the issue can be the electronic board, control panel, heating element, and other hard-to-reach parts.

    Read on for details on what makes a Whirlpool dishwasher fail to start/complete a cycle and what you can do to fix each problem.

    Whirlpool Dishwasher Wash Motor Not Working:

    Check that the dishwasher is plugged in and that power is being supplied to the dishwasher through a circuit breaker or fuse. Check if the dishwasher door latches. If none of your steps restore power. Then there may be a fault in the circuit of your dishwasher or other electrical systems of the machine.

    Don’t Miss: Bosch Dishwasher Model Number Decoder

    Consult Your User Manual

    If turning the power off and on didnt work, the next step is to find the user manual for your specific model of Whirlpool dishwasher. If you dont have a physical copy, you should be able to find an online version by simply Googling Whirlpool Dishwasher .

    Each different model has its own reset instructions, so if you find the user manual, you should check it for how to reset your dishwasher. If you cant find your manual or if the method doesnt work, start going through the next steps in this guide, which will cover all of the most common ways to reset a Whirlpool dishwasher.

    Dishwasher Wont Start: 10 Possible Causes

    Whirlpool Dishwasher DP840SWSX0 Troubleshooting &  Repair

    There are really just ten possible causes when a dishwasher wont start. Dishwashers are simple to operate, but have lots of small parts inside.

    When a dishwasher wont run, the problem can be mechanical or electrical. With our guide, you dont have to be an appliance repair expert to determine which problem is the culprit.

    Even if the fix is more complex than you can manage, being able to point your appliance repair tech in the right direction will save you time and money.

    Please note that this guide is for information purposes only. For safety, always consult a professional if you have a problem with an electrical appliance.

    Keep reading to discover the ten possible causes when your dishwasher wont start. If you dont want to mess with a DIY fix, use our form to get a free quote from a local appliance repair company.

    You May Like: Best Dishwasher Detergent For Older Dishwashers

    Whirlpool Dishwasher Problems And Troubleshooting

    Innovative technology, user-friendly controls, and special features are just three factors that set Whirlpool dishwashers apart from the rest. PowderDry extracts the steam at the end of the cycle leaving plastics dry in a single hour.

    6th sense technology automatically senses how dirty the dishes are adapting the water pressure and cycle time accordingly. And A+++ energy efficiency ensures perfect results with low power consumption. So, what happens when your dishwasher stops working? See a range of Whirlpool dishwasher problems and troubleshooting here

    Check Whether The Wash Cycle Is Complete

    To begin, make sure that the dishwasher has completed its cycle. If you accidentally open the dishwasher before it finishes the cycle, you might find it filled with water.

    Before you do anything else, look at the indicators on your dishwasher to see if a light or notch properly indicates the clean or off option. If you do not see this light, you might have accidentally interrupted the cycle. Simply close the door and press the start button again to tell the appliance to finish its cycle.

    You May Like: Are Yeti Lids Dishwasher Safe

    How To Keep My Whirlpool Dishwasher From Malfunctioning

    Like any electrical appliance in your house, your dishwasher needs care. This includes keeping it clean and following all of the maintenance guidelines provided in its manual.

    With your Whirlpool dishwasher, here are the steps you should follow regularly:

    • Clean the filter regularly. It accumulates food scraps and can get clogged very easily, causing the dishwasher to malfunction.
    • Check the inlet temperature of the water in your dishwasher. Whirlpool recommends that it should be between 50 to 60 degrees Fahrenheit.
    • If your dishwasher has a rinse aid, always check its level. It shouldnt decrease too much.
    • Install surge protection for your Whirlpool dishwasher. This helps avoid malfunctions caused by electrical outages or power surges.

    Look Into Issues With The Drain Pump

    Dishwasher Repair will not start – Repair & Diagnostic – Kitchen aid – Whirlpool

    If you have exhausted all of the above options, but your dishwasher still refuses to drain correctly, you may have a problem with your dishwasher drain pump.

    Your pump motor will likely be under the lower spray arm. It has two impellers and several other components that have the potential to get clogged with food.

    You can use your manufacturers manual to see how to take the pump apart to check for blockages. It might be better to call a professional if you do not have experience with this type of task. Consider Cinch for your home protection needs to be prepared for a moment like this.

    Read Also: How To Clean Jetted Tub With Dishwasher Tablets

    How Do I Fix The Start Button On My Whirlpool Dishwasher

    As mentioned earlier, a start button that doesnt work will make it difficult for you to use your dishwasher. The good news is that you can always use other means to activate a wash cycle. Even so, some methods may not be safe, convenient, and reliable. If you notice your Whirlpool dishwasher start button not working, use these tips to fix it.

    How To Start Whirlpool Dishwasher Without Start Button

    Its easy to start the Whirlpool dishwasher by pressing the start button. But, even with the Whirlpool dishwasher start button not working, you can still turn the appliance on. To turn the dishwasher on without a start button, follow these steps:

    • Close the dishwasher door properly.
    • Ensure that power is reaching the start button as well as the control panel
    • Reset the dishwasher
    • Activate the water inlet valve to allow water to flow into the washing compartment.
    • Start the appliance by pressing the main wall switch

    Read Also: Whirlpool Dishwasher Heating Element Replacement

    Check The Power Supply

    If the dishwasher wont do anything at all, the problem could be the power supply. Check the circuit breaker. If it has tripped, flip the switch to the off position and then turn it back on. If the circuit has not tripped, check to ensure that the appliance is properly plugged into its wall outlet. This may require you to pull the appliance out from beneath the counter. Before attempting to move the unit, disconnect the under-counter retainer clips that hold it in place.

    Why Does My Dishwasher Suddenly Have No Power

    Whirlpool Cabrio Washer Problems &  Troubleshooting Tips

    You fill your dishracks with dirty dishes then close the dishwasher doorexpecting to set the cycle, but the control panel is dead. Youre thinking to yourself, this has got to be one of the most frustrating appliance failures ever. It seems to always happen at the worst timeon the weekend or when you have company over.

    Sometimes, the problem can be resolved with the flick of a light switch.

    You may be surprised to learn that many dishwashers have a light switch beside the garbage disposal light switch. The dishwasher light switch shuts off power to the dishwasher when the switch is in the off position.

    So, the first step in troubleshooting a dishwasher that wont power up is to check that light switch. Turning on that switch may fix the problem right away and you can start the dishwasher.

    Some dishwashers dont have that light switch installed beside the sink. If you dont find such a switch or if the switch is there but its already turned on, then youll need to continue with the troubleshooting steps described below.

    Read Also: How To Deep Clean Your Dishwasher

    Whirlpool Dishwasher Stops Working Mid

    This problem is often confused with the dishwasher not completing cycle issue we tackled earlier. The difference is that when a dishwasher stops working mid-cycle, it may shut off completely instead of merely leaving you with dirty, unrinsed, or undried dishes, as is the case with a dishwasher failing to do a full cycle.

    If your dishwasher keeps shutting off mid-cycle, first try the following basic troubleshooting hacks:

    • Open the door and close it again to ensure its latched.
    • Check whether the dishwasher has water leaks or faulty plugs and cords that may be causing it to trip the circuit breaker. A tripped circuit breaker usually cuts off the power supply to the appliance, suddenly stopping any cycle that may be running.
    • If your units power supply is controlled by a light switch on a wall, check to ensure its switched on.

    If these basic hacks dont cut it, the problem could be any of the following:

    • A broken door latch
    • A faulty pump and motor assembly
    • A blown bi-thermal fuse
    • An issue with the power supply control board
    • A malfunctioning high-limit thermostat
    • A clogged/faulty circulation pump
    • Food particles in the chopper blade area

    Dishwasher Door Latch Malfunction

    Your dishwasher wont start if the dishwasher door isnt securely closed and latched. Always close the door firmly, without slamming, to ensure that the latch is engaged. A Whirlpool dishwasher not starting even with a properly closed door may have a latch malfunction. If the latch is damaged or shows a lack of continuity with multimeter testing, it must be replaced.

    Read Also: Cleaning Dishwasher With Citric Acid

    Whirlpool Dishwasher Wont Start 5 Solutions To Run

    The dishwasher is the most convenient kitchen appliance, but it can seem like an annoyance when it doesnt start as planned. Why isnt my Whirlpool dishwasher starting? You may have accidentally set the wrong option or blocked access to the control panel while troubleshooting. When your Whirlpool dishwasher wont start on.

    Whirlpool Dishwasher Heavy And Normal Lights Blinking

    Maytag, Whirlpool & KitchenAid Dishwasher – Not starting – Diagnostic & Repair

    Heavy and normal lights blinking on a Whirlpool dishwasher indicate that one or several of the key switch lines are shorted or stuck on the keypad or control board.

    To determine whether the issue is a short on the control board, use the above video guide to test the control board. If its malfunctioning, replace it.

    If the control board is okay, the issue is the keypad. Before you replace the keypad, check for any stuck keys and pop them back up with a pin.

    You May Like: Sink Tailpiece With Dishwasher Connection

    Why Does My Whirlpool Dishwasher Smell Bad

    Dishwashers do an excellent job of cleaning dishes. However, the food particles stuck to the plates, bowls, pots and pans still end up somewhere. These little pieces of food can get lodged inside the dishwasher if you dont clean out your appliance regularly. Over time, this food can begin to rot and grow bacteria, leading to a bad smell coming from your dishwasher.

    The best way to solve this problem is to give your dishwasher a good cleaning. Remove the bottom dish rack and clean out any food buildup trapped along the bottom or sides.

    You can also look at your manufacturers instructions to see how to use a screwdriver to uncover the dishwasher filters and clean them. Before taking the filters out, ensure you understand the filter assembly so you can put them back together. Getting rid of this grime can help eliminate foul odors.

    Whirlpool Dishwasher Clean Light Blinking 7 Times

    This is one of the most common issues on Whirlpool dishwashers and can be caused by defects in the heating element, control board, thermostat, wash motor, or water inlet valve. It can also occur due to a clogged sump filter.

    To fix the issue, youll need to use an elimination method. Heres how to go about it:

  • Inspect the heating element for signs of electrical shorts. If any, replace the element.
  • Use a voltmeter to test the control board. Run your dishwasher for about 10 minutes, or until it reaches the second wash cycle. Next, test the heater to see if its receiving power from the control board. If not, test the thermostat to see its the issue. If the thermostat checks out, replace the control board because this means its not sending power to the heater.
  • Run a diagnostic cycle. When the dishwasher is done filling, check the water levelit should be slightly below the heater. If its way below or theres no water at all, the inlet valve is the culprit and needs replacing.
  • If you still havent found your culprit at this point, run your unit and quickly open the door in the middle of the cycle. If water doesnt spray out when you do this, or there isnt any dripping from the top dish rack, the motor is likely the problem. To fix it, check the bottom filter for clogs and remove them, if any.
  • Read Also: Can Caraway Pans Go In The Dishwasher

    RELATED ARTICLES

    Most Popular