Clearing The Error Code Lc On A Samsung Dishwasher
The LC fault code appears when the leak sensor detects excess moisture in the unit, which may suggest a leak. However, this may be a glitch. Disconnect the unit from the mains and wait about 15 minutes. Plug it back in and try a cycle again. In most cases, the error disappears. If it does not, there is either a leak sensor issue or there is a leak indeed.
NOTE: the error may occur due to moisture in the base of the unit, which is not necessarily due to a leak. Therefore, this leak error code may have several explanations.
LC or LE flashing on your Samsung dishwashers display means Water Leakage Error.
The leak sensor has detected moisture or leak in the machine.
Check your machine for leaks. If there is a lot of water in the base, most likely, there is a good reason for the code to appear. Follow the link and see how to fix the problem.
If no leak is found, see other causes of the LC / LE error.
Half Load Function Error
Half load function or PE error appears when the Dishwasher half load function is not performing well.
First of all, to fix this error, remove all the utensils and clean the Dishwasher. After this, add detergent and run half load cycle on the Dishwasher.
See if the error appears or not.
These are commonly found error codes in the Samsung Dishwasher. Besides this, we have not covered a couple of remaining LC codes in this list.
The remaining errors are rarely seen in the Samsung dishwasher, so we have not covered this list.
May Required in Future:-
How To Repair A Leaking Dishwasher
There are specific reasons why your dishwasher is leaking. Fortunately, these reasons are easy to fix in simple DIY steps. In most cases, a leak in a dishwasher comes from a part within the washer, or the bottom of the machine or from the front of the dishwasher. To fix this problem, you need to examine the appliance, locate the point of weakness and fix the leak. Here are some of the potential causes of leaks within your Samsung dishwasher.
Leaking Door Seals
When the door seal leaks, water will appear on your kitchen floor in front of your dishwasher. However, you need to confirm this by opening the dishwashers door and inspecting the seal around your machines front door to ensure it is not worn or ripped. Once you identify the damaged area in the door seal, you need to remove the faulty part and replace it with a new seal.
However, if the water is coming from your dishwashers bottom, then something is leaking under your dishwasher tub. In most cases, the water inlet valve or the water pump seal causes the bottom leak.
Using the Wrong Detergent
Before inspecting your dishwasher for faults, you have to ensure that you are using your manufacturers recommended detergent. The wrong detergent can lead to excess formation of suds. When this suds overflow, they can appear as drips on the outer part of your dishwasher. Therefore, you need to start using the right detergent in your dishwasher.
Leaking Water Valve
Leaking Pump Seals
Leaking Hoses
Stuck or Damaged Float Switch
Don’t Miss: How To Unclog Dishwasher Drain Hose
Overfilling Dishwasher With Detergent
While you may be tempted to overfill the detergent dispenser, this is actually a bad idea because it can trigger the machine into showing the LC error code. Overfilling the dispenser makes the machine to detect excess detergent, but you can correct this potential problem by reducing the amount of detergent in your dispenser.
Questions To Ask Yourself When You Doubt A Samsung Dishwasher Leak
There are many reasons for water leakage in a Samsung dishwasher. If you suspect a leak, you should ask yourself the following questions:
1. Did you recently install or move the Samsung Dishwasher?
If you recently installed or moved the dishwasher, the leak sensor may have accidentally gotten some moisture on it, resulting in the LC error code. If that is the case, you should wait for the water to dry and reset the dishwasher. This might just solve your problem.
2. Did You Put a Lot of Detergent?
Many people make the mistake of overdoing it when they fill their dishwasher with detergent. Your appliance might detect the excess detergent and start showing the LC Error Code. It would help next time to use less detergent in the machine.
3. Did You Connect the Dishwasher to Garbage Disposal?
Recently connecting a garbage disposal to the dishwasher and forgetting to remove the cap can also lead to the LC error code. To fix the situation, all you need to do is remove the cap and reset your dishwasher. Also, do the garbage disposal right the next time!
Read Also: Whirlpool Dishwasher Not Drying Dishes
Check For Defective Components Causing The Leak
A Samsung dishwasher LC error code is typically caused by a defective spray arm, seal, water inlet valve, pump, or leak sensor.
If a dishwasher spray arm is damaged, water may be spraying in the wrong direction and causing water to seep into the base of the dishwasher. Before removing any access panels, make sure the spray arms are not damaged or clogged. If a spray arm is damaged, replacing it may resolve the LC error code.
Checking the remaining components will require accessing the base of the dishwasher.
The Reason Behind Samsung Dishwasher Lc Error Code
We have discussed different types of LC code errors on the Samsung dishwasher. LC codes help us understand and fix the error inside the Dishwasher.
These error codes are caused due to various reasons there is no specific reason for this error. Putting this in perspective, here we have brought a list of the reason behind the LC codes error:
These are some of the primary reasons behind the LC error codes on the Samsung Dishwasher. Apart from this, there are various reasons for the LC error code.
But, these are some of the significant reasons which could force dishwashers to emit these errors. Restarting the Dishwasher could solve most of the error codes.
But, first, you need to turn off the Dishwasher and have to wait for around 10 to 15 minutes.
Don’t Miss: Where To Put Detergent In Dishwasher
Why Is My Dishwasher Flashing Lights
A flashing Washing light on your dishwasher could be a sign of something amiss with the volume or temperature of the water. It could also be an indication of too much foam or suds in the washtub. Your washer will not run as long as the light is flashing. Start by resetting your machine’s control panel.
Repair Or Replace Faulty Leak Detector
If the problem is with your leak detector or drain pump, you can easily repair or replace it to get your appliance functional again. Sometimes, repositioning the leak detector will remove the LC error problem.
If this is not easy for you to do, get a local technician to examine the unit and get the appropriate replacement parts for it. This will fix the Samsung dishwasher LC code problem in no time.
Recommended Reading: Bosch Dishwasher Replace Drain Pump
What If The Issue Is Still Not Identified
If you have tried all these questions and the issue is still not identified, you dont need to panic. Simply follow the steps below, and you will probably get rid of the Samsung dishwasher error.
1. Disconnect it
The first step, for your safety, is to disconnect the dishwasher from the power source. You also need to turn the breaker off.
2. Get Access
When you want to remove your dishwasher from under the counter, you will find small clips fastened with some screws.
First, you need to remove the screws and slide the machine so that you can hold its bottom. Then you need to turn the machine on its side to get access to the area you need.
After turning the appliance on its side, you need to access the bottom panel. In some cases, there might be a tray here. The role of this panel or tray is to stop water from leaking to the floor beneath it.
There is a bowl in the middle of the bottom panel or tray. It is the sensor that sends an error code if there is water leakage.
3. Clean the Area
If there is water in the panel or tray, you can remove it using a dry cloth. Take away as much water as you can gently.
Relocate the Leak Sensor
The leak sensor is present in the drain pan or the bottom of your appliance. The next step is to find it and relocate it so that the error code doesnt pop up again if there is slight moisture.
Re-Secure the Dishwasher
Turn it On
The next step is to turn the dishwasher on by plugging it in and then see whether the error code LC is still there or not.
Locate The Leak Sensor
The leak sensor is located on the floor of the dishwasher near the drain. Once you locate it, then again locate it some inches above so that it would stop the LC error if the error is just the cause of this moisture. Also, check the drain hoses because they can also leak. If you find this then repair it otherwise the LC error would occur again and again.
Also Check: Ran Out Of Dishwasher Tablets What Can I Use
How To Remove The Samsung Dishwasher Lc Code
The simplest way to fix Samsung dishwasher LC Code is to unplug your kitchen appliance and wait for about 10-15 minutes. After that, you can plug in the power cord and restart the dishwasher. Usually, this simple step will reset the dishwasher and ensure that this Samsung dishwasher error goes away.
What if the Samsung Dishwasher LC Code is Still There?
If you have unplugged and replugged the appliance and the error code is still there, you need to consider whether you might have a faulty sensor or a water leak. Dont panic if either of these is true, as theres a proper solution for everything.
Sometimes, the bottom pan might be wet, and your dishwasher might show the LC code. You can just clean it with a soft cloth in such a scenario, and the error code will go away.
How to Find Out If You Have a Leaky Dishwasher and the Error Code LC is Correct?
If the solution mentioned above has not worked, likely, you might have a leaky dishwasher.
To check for a leak, you need to unplug the dishwasher, pull it out from the countertop and then take off the metal panel situated on the right side. Doing so will allow you to get access to the drain pump so that you can detect any visible water leakage.
If you can see water leakage around the drain pump, this confirms that your dishwasher has a water leakage problem and the LC error code was correct. It will also ensure that the leak sensor is working just fine.
What Is The Meaning Of Lc In Samsung Dishwasher
Error LC specifies a leakage of water in the Samsung dishwasher. In other words, it means there is water leaking from the system of the Samsung Dishwasher. The moisture can also be the reason for the LC error code in the Samsung dishwasher. Your dishwasher may detect there is a water leak because the bottom pan is damp or damp with moisture. You might have a chance at solving the problem that way.
Don’t Miss: Sink Backs Up When Dishwasher Runs
Overview Of Samsung Dishwasher Error Codes
This code indicates that the leak sensor has detected a leak of water or moisture from somewhere inside the unit. This can be caused by genuine water or moisture leak from a broken water line or connection in some cases.
It could, however, be caused by residual water or moisture in the dishwashers bottom pan. Finally, your dishwashers leak sensor could be faulty, explaining why youre getting the LCerror code.
Samsung Dishwasher Is Showing An Lc Error Code
Jun 4, 2021·
One of the most frustrating situations is when you finally decide to take care of those chores you have been avoiding all week and you discover that the appliance isnt working properly. Almost all brands are prone to these issues and a Samsung dishwasher is no exception.
This feeling can be especially frustrating when you dont know what the issue is and what to do about it.
Whenever your Samsung dishwasher is facing an issue, it will let you know about it through an error code.
If the error code is LC in a Samsung dishwasher it means that there is a leakage issue in your machine. This is either due to a faulty error system or if your machine is facing an actual leakage because of a drain pump and/or if there is some moisture stuck in the bottom pan.
Lets take a look at what you can do in these situations..
You May Like: Ge Dishwasher Heated Dry Not Working
How To Remove Samsung Dishwasher Lc Error Code
LC code indicates that there is a leak somewhere in the dishwashers water supply system. There may be a faulty leak sensor, or there may be a water leak, but regardless, you should run through a cycle with your dishwasher to check for leaks.
If your Samsung dishwasher has a leak detection code and you have already checked for any external leaks, try to remove the bottom pan from the dishwasher and check it for excess moisture or dampness. If the water trap pan is wet, try to dry it.
To get your dishwasher running at peak performance again, follow the troubleshooting steps below.
Licensed Dishwasher Repair Service
Get a professional dishwasher repair technician from The A Team Appliance Repair to diagnose the problem with your dishwasher. With our in-home, same-day dishwasher repair service, you can expect to have the problem repaired quickly, avoiding or minimizing damage to your household. Our professional, licensed technicians arrive with everything they need to diagnose and remedy the problem at hand.
- Water is not filling the dishwasher
- The water is not draining correctly
- The detergent is failing to release
- Dishes come out dirty
- Dishes are wet at the end of the cycle
- The dishwasher is making unusual noises
- The cycle will not start
Types of Dishwashers We Repair
Our professional technicians are licensed to repair all types of imported and domestic dishwashers, including
- Built in Dishwashers
Quality & Reliable Service at Reasonable Price
TIME
We know your time is valuable, whether its a rental property , your own property, or your business, we will be there in no time, in order for your to go back to your daily business, with as little disruption as possible.
QUALITY
Just because our technicians work fast, does not mean that it isnt done right. Our technicians are highly experienced and use brand new, original, and high quality parts needed to complete the repair of your appliance.
PRICE
Book Your Repair
Also Check: How Do I Fix My Dishwasher Leaking From The Bottom
Fast And Professional Residential Appliance Services
Need appliance repair service? Call our number. One of the most significant things when you work with our company is that we are easy-to-find technicians. Organized in a way to help clients in a timely manner, we can help you really fast when problems in the kitchen or laundry room pop. Allow us to offer:
- Emergency freezer and refrigerator repair
- Oven installation and repair services
- Stove & range repair
Oven & Stove Repairs
Refrigerator Repair
Our appliance technicians are licensed to fix all household appliances. In spite of their brand, size, type and model, we can repair them and actually help our Richmond Hill customers as fast as possible. We have experience in all household appliances in Ontario at our Appliance Repair in Richmond Hill and travel with repair parts in our trucks to quickly repair the damage. From motors, compressors, valves and gaskets to evaporators, coils and switches, all parts can be replaced once they are broken or ruined. Trust our team to offer routine appliance service, fix issues, and take care of your household appliances to your satisfaction.
Appliance Repair Experts In Richmond Hill, ON
For Fast Service, Call Us NOW: 647-660-4513
Samsung Dishwasher Lc Error Code
Ideally, when the LC or LE error code shows on your dishwashers digital display, it is an indication of water leakage from the appliance. This happens when the dishwasher sensors detect moisture or water leak in the machine. Before you make a conclusion about the error code, you need to troubleshoot your dishwasher and determine the exact issue causing the error code. Sometimes the error is a false alarm due to your sensors misreading.
Important: If you use Amazon a lot, you can enjoy FREE same-day delivery as well as FREE Two-Day Shipping on millions of items for . Sign up in 2 seconds with the click of a button if you’re already logged into Amazon.If you’re still struggling to find good shows to watch on Netflix, you can also enjoy instant streaming of thousands of movies and TV shows. Other Prime perks include unlimited, ad-free access to over a million songs, borrowing books for FREE from the Kindle Owners’ Lending Library, and skipping the lines with 2-hour delivery on a wide selection of fresh ingredients.
Recommended Reading: Replacement Parts For Samsung Dishwasher
Check Whether The Tub Sides Are Stretched Or Bowed
D the cabinet screws on your Samsung dishwasher are over-tightened, the tub may stretch at the sides. Thai creates gaps, allowing water and moisture to leak out. To rule this out, measure across the door opening especially where the screws are located. Normally, it should be 22 inches long.
If it measures more than 22 inches, you should loosen the cabinet screws until the issue is corrected. If you happen to be using a Samsung Waterwall model, ensure that there are no utensils or dishes obstructing the movement of the reflector. This has also been proven to trigger the Samsung dishwasher error code LC.