Pull Out The Dishwasher
Position the dishwashers power cord so it moves freely as you pull the dishwasher out from under the counter.
Place a towel under the water supply line connection. Disconnect the water supply line from the water inlet valve and wipe up spills.
Disconnect the drain line from the garbage disposal or sink drain.
Remove the 2 mounting screws from the brackets that secure the dishwasher in the cabinet opening.
Uninstall The Old Heating Element
Now you are ready to access and remove the old heating element.
- Remove the Lower Dish Rack
- Open the dishwasher and remove the lower dish rack. You will need this space to access the heating element underneath. If you want, also remove the upper rack.
W10518394 Dishwasher Heating Element Replacement For Whirlpool Wdf310paas2
- UpStart Components Replacement W10518394 Dishwasher Heating Element for Whirlpool WDF310PAAS2
- Ultra durable, high quality material resists wear and tear over time. Easy at-home installation.
- An affordable way to extend the life of your machine.
- Please make sure to check your original part to confirm that you are buying the correct product.
- Compatible W10134009 Heater Element for Part Number W10518394, AP5690151, 2977737, 8194250, 8563007, 8572861, PS8260087, W10134009, W10441445, W10518394VP
You May Like: Dishwasher Leaking Bottom Of Door
Cause : Faulty Vent Fan Motor
The vent fan blows the steamy air out of the aforementioned vent. If the vent door is opening properly but the fan motor has failed, most of the steamy air stays trapped in the dishwasher. Remove the fan motor and use a multimeter to test it for continuity. If theres no continuity, replace the motor.
Whirlpool Dishwasher Heating Element Not Working

If you get the error code that the heating element is not working it is possible to repair it yourself. However, if you dont have much experience working with tools you can have a repair guy do it for you. Heres a summary of what you should do when your Whirlpool dishwasher heating element is not working:
Generally, the heating element will be replaced with a new one. They can be purchased online for roughly $80. To install one yourself is very easy. However, someone with experience working with tools would do it much quicker. The whole process takes less than 5 minutes to complete.
The old element is unplugged and then unscrewed. After that you simply screw in the new one and plug it in. Below I will explain how to do it step by step. However, its important to note that a repairman could install it for you for around $150.
When the heating element is not working there can be a visible crack in the heating element. The heating element is a ring that goes around the bottom of the dishwasher. There can also be a notch on it. Both of these indicate that the heating element needs to be replaced.
If you dont have good mobility or prefer to have an expert do it, I suggest hiring someone to replace it for you. Its likely simpler to have them order the replacement element for you.
You need to get underneath the dishwasher with an adjustable spanner which can be difficult to reach. Heres a video that shows how to replace a broken heating element:
Heres a summary of the steps:
You May Like: Dishwasher Vs Hand Washing Water Use
Shut Off Electrical Power And Water Supply To The Dishwasher
Unplug the dishwasher or shut off the house circuit breaker for the dishwasher.
To verify that power is disconnected, make sure the control panel doesnt light up when you press a control button or the power button.
Find the water supply valve for the dishwasher under the sink . Close the valve to shut off the water supply going to the dishwasher.
Cause : Faulty Heating Element
The heating element lies inside your dishwasher near the bottom, and helps get the water hot enough to turn it into steam so the aforementioned fan can blow it out and leave everything inside nice and dry. If the heating element fails, the water never gets hot enough to evaporate.
To check the heating element, run a wash cycle using the heated dry feature, and open the dishwasher door in the middle of the dry cycle. It should be steamy hot inside, and if you wave your hand over the heating element , you should be able to feel the heat coming off it.
If theres no heat, you may need to replace the heating elementtry removing it from the dishwasher and then use a multimeter to check the resistance of the heating element. It should measure somewhere in the range of 8-30 ohms. If resistance is infinite, replace the heating element.
You May Like: Quiet Partner 2 Whirlpool Dishwasher
How To Put It In Diagnostic Mode Then What To Do
After it has finished it will display the error code on the screen. There is a panel at the front of your dishwasher that will come off if you pry it open with your hands. And inside that space is a sheet of paper that will tell you what all the error codes mean.
Then depending on what the error code is you can do the corresponding repair for it. For example, it may not necessarily be the heating element that is broken.
But, the only way you can know is to run it in diagnostic mode. A full list of all the error codes is also available online on the official Whirlpool website here.
Deeloy W10134009 Dishwasher Heating Element Replacement For W10518394 8563007 8572861 Lp14302
Was: |
- Replacement for the most top brand.
- Replacement for the following part numbers: W10518394 W10134009, 8563007, 8572861, LP14302
- Fits the following models: 7DU1100XTSQ1, 7DU1100XTSQ2, 7DU1100XTSQ5, 7DU1100XTSS1, 7DU1100XTSS2, 7DU1100XTSS4, 7DU1100XTSS5, 7GU2300XTVQ0, 7GU2300XTVQ1, 7GU2300XTVQ2, 7GU2300XTVQ3, 7GU2300XTVS0, 7GU2300XTVS1, 7GU2300XTVS2, 7GU2300XTVS3, 7WDF530PAYM0, 7WDF530PAYM1, 7WDF530PAYM and more
- If your not sure about the compatibility, please contact us for confirmation.
- It does not replacement for Whirpool WDT710PAYM5
- This item: Deeloy W10134009 Dishwasher Heating Element Replacement for W10518394 8563007 8572861 LP14302$32.99Sold by Deeloy and ships from Amazon Fulfillment.Get it by Wednesday, Aug 10
- Sold by PrimeCo Supply and ships from Amazon Fulfillment.Get it by Wednesday, Aug 10
- Only 9 left in stock.Ships from and sold by Lupus Wolf.Get it
Read Also: Best Rated Dishwashers For 2022
Defective Whirlpool Dishwasher Parts
If none of the above measures result in dryer dishes, its possible that one of your dishwasher components is defective. These components are often the cause when a dishwashers drying function malfunctions:
- Failed Whirlpool dishwasher vent: Some dishwashers use a vent to let out damp air after a wash cycle, ridding dishes of moisture. If the vent doesnt open properly this moisture will be left on dishes. A broken vent requires replacement.
- Broken fan motor: Dishwasher vent systems often use a fan to propel moist air through the vent and off dishes. If the fan blades dont turn freely and the fan motor has no continuity, the motor needs replacement.
- Defective Heating Element: Other dishwashers use a heating element to dry dishes after theyre washed. When the heating element isnt operating correctly, your dishes will remain wet. If multimeter testing of the heating element reveals a lack of continuity it needs to be replaced.
When your Whirlpool dishwasher leaves dishes wet or experiences any malfunction, let Moore Appliance Service be your go-to dishwasher repair service provider.
Recommended Reading: Replacement Parts For Samsung Dishwasher
Cost To Replace The Dishwasher Heating Element
The amount youll spend on replacing your dishwasher element depends on if youll be hiring a professional or doing it yourself.
A dishwasher heating element costs between $30 and $90.
If youll be doing it yourself, youll save the cost of paying a professional. Youll also need pliers, nuts, and a wrench.
If you have those tools already, youll only be spending 90 dollars maximum which is the cost of the heating element. If you dont have them, then you will need to get them which will put the total cost above 100 dollars.
If youll be hiring a professional, get ready to pay between 100 dollars and 150 dollars. Adding that to the cost of the dishwasher heating element, you may spend between 130 dollars to 200 dollars. Maybe even more.
Recommended Reading: How To Unclog Bosch Dishwasher
Lg Lfc28768st Refrigerator Will Not Make Ice Water Inlet Valve
ApplianceVideo.com is a free online portal for all of your Appliance DIY repair needs. With a growing library of free repair videos, we have the video you need to complete your next repair with confidence. Our videos have been produced, reviewed, and tested by our factory certified technicians with over 30 years of infield experience.
Whirlpool Dishwasher Not Drying

What to do when your dishes aren’t dry at the end of a wash cycle? Try these fixes first.
If your dishes are still dripping wet after a wash cycle, first check your dishwashers owners manual to make sure its being operated correctly. Many manufacturers recommend using a liquid rinse aid for proper drying performance. Additionally, if your homes water temperature isnt hot enough to begin with, this can hinder drying performanceso adjust the temperature setting on your water heater if needed.
But if none of that helps, there may be an actual hardware issue with your dishwasher. In that case, check the following.
Recommended Reading: Bosch 500 Vs 800 Dishwasher
How To Replace A Dishwasher Heating Element
This DIY repair guide gives step-by-step instructions for replacing the dishwasher heating element. The heating element at the bottom of the dishwasher tub heats water during the wash and rinse cycles and air during the heated drying cycle. If the heating element is damaged or won’t heat even when it gets electricity, replace it with a manufacturer-approved dishwasher part. Follow the steps below to replace the heating element in your dishwasher.
This guide can help you replace the heating element in Kenmore, Whirlpool, KitchenAid, Maytag, Amana, JennAir, GE, Frigidaire and Electrolux dishwashers.
How to replace a dishwasher heating element video.
Cause : Faulty Support Components For The Heating Element
If the heating element checks out, you may have a heating element control board failure, wiring failure, thermostat failure, or limit switch failure.
Unplug the power to the dishwasher and shut off the water supply, disconnect the drain plug , disconnect the water supply , and pull the dishwasher out from the wall. Disassemble the dishwasher enough to check the wiring connections to the heating element and make sure theyre tight. Check the wiring to the thermostat in the same way if necessary, remove the thermostat and test it with a multimeterresistance should measure near zero ohms.
Your dishwasher may have a limit switch, which is a safety feature designed to switch off the heating element if it gets too hot. If the switch fails, the heating element may not come on at all. Remove the switch and test it for continuity if it fails, replace it.
If none of that helps, you may need to replace the electronic control board for the heating element.
Read Also: Bosch Dishwasher Silence Plus 46 Dba
Signs Your Dishwasher Heating Element Is Faulty
While your dishwasher may be hooked up to the hot water line, every dishwasher uses a heating element to heat the wash water up to the appropriate temperature. Found in the bottom of the tub, you may recognize the heating element if you have an electric oven as they serve the same function, in a way. However, there may come a day when your dishwasher starts throwing out some peculiar symposiums. If any of the below are manifesting in your dishwasher, it may be time to replace the heating element.
Replacement W10518394 W10134009 Dishwasher Element For Maytag / Whirlpool
Replacement W10518394 W10134009 Dishwasher Element for Maytag / Whirlpool
- Orders placed by 4pm ET ship today!*
Replacement heating element used for some Inglis, Maytag, and Whirlpool dishwasher models.
Directly Replaces: W10518394, 8194250, 8563007, 8572861, W10441445, W10134009, W10518394VP, B0156NFVP4, B0035G56DM, B005AR7B0U, B008DKBIX2, SAPW10134009, 2977737, AP5690151, EAP8260087, PD00004893, PS8260087.
Features:
- Heats the water to a temp high enough to remove bacteria from dishes. Also used to dry dishes faster.
- Includes: Heating Element, Washers, Fasteners.
- Included rubber washers ensure a water tight seal.
Specifications:
- Material: Calrod element with rubber washers and plastic fasteners.
- Overall Dimensions: 16 9/16â³L x 16â³W x 3â³H.
- Additional Dimensions: Threaded ends are 7/16â³ diameter.
*Please be mindful of the width of the threaded ends prior to purchase. Some compatible models may require the element holes to be widened slightly with a drill to fit the threaded ends of this part.
Don’t Miss: Ge Dishwasher Orange Light Flashing
Install The New Heating Element
Lubricate the seals on the leads of the new heating element with a small amount of rinse aid.
Push the leads of the new heating element through the holes in the back of the tub.
Attach the mounting clip inside the tub to the new heating element.
Set the dishwasher on its back.
Install the plastic nuts on the ends of the leads don’t cross-thread the plastic nuts.
Tighten the nuts until they’re snug, to prevent leaks.
Push the wires completely onto the leads of the heating element.
Set the dishwasher upright. Pour water into the dishwasher. Check for leaks around the plastic nuts. To stop leaks, tighten the nuts to seat the rubber seals.
Reinstall the bottom dishrack.
Tilt the dishwasher upright and carefully push the dishwasher under the counter.
Reconnect the drain hose to the garbage disposal or sink drain.
Reconnect the water supply line to the inlet water valve.
Insert the screws into the mounting brackets that secure the dishwasher under the counter and tighten the screws.
Position the toe panel on the dishwasher and then position the access panel in front of the toe panel. Insert and firmly tighten the mounting screws.
Tip: If the dishwasher hardwires into a junction box, push the power cable into the junction box and reinstall the strain relief nut. Reconnect the wires in the junction box and reinstall the junction box cover.
Whirlpool Dishwasher Not Drying Dishes
You might have been running your Whirlpool dishwasher without any issues for quite a while but then noticed that the dishes are still wet at the end of the cycle. This typically indicates a problem with the heating element. Heres how to fix it.
Run the Whirlpool dishwasher in diagnostic mode. It is put in diagnostic mode using a special combination of keys on the control panel. As part of diagnostic mode it will test each part of the dishwasher and report where the error is. The heating element can also be inspected and will show signs that it is broken.
The steps to put your Whirlpool dishwasher into diagnostic mode is covered under the heading just above this one that says How to put it in diagnostic mode and what to do.
Follow those instructions and then see what it says. After some time around 10 to 20 minutes it will display an error message for what is causing the issue.
The heating element should also have a completely smooth round surface. When there is an issue with the heating element a notch will develop on the surface of the heating element. The heating element can also crack, which will be visible on the otherwise smooth flat surface of the heating element.
Where the heating element is either cracked, has a notch on it, or needs to be replaced because of the error message you receive, then you can replace the faulty heating element very easily.
Read Also: Ge Dishwasher Beeps 3 Times
How To Replace Your Dishwasher Heating Element
Your dishwasher is a remarkably self-contained machine. Not only does it wash, rinse, and dry your dishes it also has an internal heating system. The dishwasher heating element can heat water or create heat to dry dishes. The heating element is an essential part of having clean dishes with a basic kitchen setup. The heating element ensures your dishwashing water is boiling hot, and is also why plastics notoriously can only go on the top shelf.
But when that heating element burns out, the signs are unmistakable. Your dishes may be less clean because their wash water is not as hot. Your dishes may be cold and still dripping wet when you open the dishwasher because the element isnt supplying that toasty drying heat. So if your dishwasher heating element has stopped working, heres how to replace it.
Instructions are generalized to cover the average dishwasher in USA, and instructions can vary by model.
Dishes Not Loaded Properly

Overloading and improper loading of the dishwasher are two of the most common reasons a Whirlpool dishwasher doesnt dry effectively. Avoid overloading by leaving adequate space for air to circulate between each item. We also suggest these rack-by-rack loading tips for a better drying function:
- Top Rack: Place glasses and bowls upside down for better rinsing, which promotes faster and more effective drying.
- Bottom Rack: Make sure dishes dont touch and are facing inward for better rinsing and air circulation
- Silverware basket: Avoid nesting by alternating spoons, forks, and knives next to each other. If the silverware basket has designated compartments, put one item in each compartment.
Image from Whirlpool
Read Also: Ge Dishwasher Heated Dry Not Working
Also Check: Why Dishwasher Is Not Draining