Check The Ge Dishwasher Main Board Service Light
An LED is typically added to the main board of GE dishwashers to facilitate diagnostics.
An excellent way to check if the board is receiving voltage is to access the mainboard and check the status of the service LED.
If the LED is off , the unit is most likely not powered, so you should try these steps:
Check if there is power in your house .
Check the control voltages if there is power .
Indeed, not turning the issue of GE dishwasher can also be a reason for low voltage or no power.
If improper voltage was found, the main control board should be replaced. .
Reminder: You will be contacted by the seller to ask for the model # before ordering, so be sure to double-check your GE dishwasher model number .
Ge Dishwasher Not Starting Light Blinking
Here are some possible causes and solutions to fix the problem.
One potential reason your GE dishwashers not starting light is blinking could be due to a power issue. Make sure the dishwasher is plugged into a working outlet, and if it is, try resetting the circuit breaker.
Another possibility is that the door isnt closed properly. check to make sure the door is shut all the way and that theres nothing blocking it from latching.
If neither of those solutions fixes the problem, then its likely an issue with the dishwasher itself. You can try resetting it by unplugging it for 30 seconds and then plugging it back in. If that doesnt work, you may need to call a repairman.
If You Do Not Select A Wash Cycle
Dishwashers cannot operate themselves because they are not robots. So, you have to give them a command for them to obey.
When you do not select a wash cycle, your dishwasher will not work. So, it would be best if you gave the dishwasher a particular command to work.
Please, do the right thing so that you can avoid delays or setbacks.
Recommended Reading: Frigidaire 24 Stainless Steel Built-in Dishwasher With Evendry
The Dishwasher Is Not In Line With The Power Source
A dishwasher will not begin its cycle if there is no power. All electrical appliances require energy to function and cannot do otherwise.
So, if the power cable is not in line with the socket, it will not come on. Now, a few things could cause the dishwasher to disconnect from power.
For instance, if your child tempered with the power cable, it may be halfway from the socket. Consequently, the dishwasher will not have power when you turn it on.
Another instance is that you moved the dishwashers power cord during cleaning. This mistake is common as cleaning the kitchen is one way to be healthy.
But, of course, if you confirm the connection, you are ready to begin the wash cycle.
Fixing The Door Latch Or Switch

First, you need to ensure no dishes are disturbing the dishwasher door. Then, please make sure the racks inside are in their proper position.
Next, make sure the door isnt having issues with closing correctly. To fix the door issue, you need to repair the hinge screws until it makes a clicking sound when the door closes.
You can use an Allen wrench to tighten or loosen the two screws on both sides of the hinges. First, you need to make sure they are equally tight.
Also, the screws need to have an equal number of turns for accurate alignment. So, you need to note the number of times you turn each screw.
Furthermore, it is essential to check your GE dishwasher door latch. The control panel will only get the start signal if the door latch works properly.
To check the dishwasher door latch:
- First, shut the door.
- Then, check the door latch connection with the unit.
- You must replace the door latch if the door doesnt close firmly.
- But if the door latch has no issue, you must check the door switch and ensure it works perfectly.
Use a multimeter to test the door switch and ensure continuity. If there is none, you would have to replace the door switch.
You May Like: Memorial Day Sale Bosch Dishwasher
Check The Power Supply
The most obvious place to start is to check the power supply. If your dishwasher isnt getting power, it wont be able to start.
To check if the power supply is working:
Turn Off The Power Before Disassembling The Dishwasher
Sometimes internal components malfunction and need to be replaced. If you are an experienced DIYer, you may be able to repair the broken dishwasher yourself, but before opening the machine to work on it, be sure to disconnect it from the power source. Use a multimeter to test internal components. Obtain a wiring diagram for your dishwasher model to ensure that you are testing the correct terminals.
You May Also Be Interested In Dishwashers Available On Home Depot
Don’t Miss: Bosch Dishwasher Memorial Day Sale
Inspect The Door Latch
When the door latch is not engaged, a switch prevents the dishwasher from starting. Listen for the sound of the latch clicking into place when you close the door. With the door closed, pull on the door to see if it is closed securely. Visually inspect both sides of the latch for anything that may be preventing it from engaging properly, and for broken parts. If the latch is broken, the switch may be also.
What Are The Reasons Why There Be No Lights On The Dishwasher Control Panel
The first thing to consider is whether the dishwasher has power. Its easy enough to test by plugging in another appliance or turning on a light, but it might be that there are other factors that have caused this problem. For instance, children playing with your machine can easily switch off both hot and cold water supplies at the same time.
If you dont have any lights on the dishwasher control panel, its worth checking that there is power to your machine. You can do this by plugging in another appliance and seeing if it works. If not, then consider contacting a plumber. It could be as simple as an issue with the main power source or the dishwashers wiring.
If this is not the issue, it could be that there are no lights on your machine because of a safety feature designed to stop children from using it without an adult present. Most machines have locks that prevent them from being used when they are in certain settings. This can also cause other problems if you want to use it for a different cycle or if the water supply is not hot enough.
If this does seem to be your problem, youll need to consult with your manual in order to reset the dishwasher properly so that you can start using it again. The machine should have come with one when you bought it, but do check online too because it might be available in a downloadable version.
Also Check: Are Sodastream Bottles Dishwasher Safe
Check The User Interface Control Wiring
Many dishwashers have a user interface control in the control panel that connects to the electronic control board.
If the dishwasher still isnt getting power, check the user interface control wire harness. The control panel wont light up if the wire harness is disconnected.
- Shut off power to the dishwasher.
- Open the dishwasher door and remove the Torx screws from the outer edges of the inner door panel. So the outer door panel doesnt fall off, support it with one hand as you remove the final screws.
- Check the wire harness connection between the user interface control and the electronic control board.
If the user interface control wire harness is unplugged, reconnect it. Reassemble the dishwasher and restore power.
Consider Using The Appliance Without The Lights
Its highly unlikely to find a newer model dishwasher working without the control panel lights on. If thats the case with yours, however, you can consider using the dishwasher with external lighting. Grab a flashlight, and you can use the appliance easily. This is a lesser hassle than going through the troubleshooting process, which can inadvertently lead to more serious damage.
You May Like: Fisher And Paykel Dishwasher Parts
Ge Dishwasher Has Power But Wont Start
If you have voltage available but the Ge Dishwasher no power or still does not work, then Check for Continuity
Check for Continuity
Ge dishwasher has no power, If there is power available at the dishwasher control panel board, we need to check if there is continuity between these power supply wires and the dishwasher motor. Continuity simply means that there is a complete path for electricity to flow. For this test, you will again need a multimeter.
Locate the two wires coming from the mains power supply and N wires that you tested for voltage in the previous section). Follow these wires until you reach the dishwasher motor. You should see two more copper wires going into the top of this motor one marked L and one marked N.
Carefully remove any insulation on these exposed wires using a knife so that you can make good contact with your multimeter probes. Now place one probe of your multimeter onto the L wire and the other probe onto the N wire. If there is continuity, then you will see a reading on your multimeter.
If there is no continuity, then this indicates that there is a break in the circuit and the dishwasher motor will need to be replaced.
Fuse Is Blown/Circuit Breaker Is Tripped
Another possibility is that a fuse has blown or the circuit breaker has been tripped. To check if this is the case, locate your homes fuse box and find the fuse or breaker labeled Dishwasher.
Faulty Drive Motor
The drain line is blocked
Test The Selector Switch

Selector switches determine the wash cycle settings for each load. They are normally located on the control panel. Test each button individually. Remove the switch from the panel. With the multimeter set on Rx1, touch the probes to the switch terminals. It should produce a reading of infinity. Then, with the probes still touching the terminals, press the button. This should produce a reading of zero. Replace the selector switch if you get any other readings.
Also Check: Drain Hose For Whirlpool Dishwasher
Not Stopping After Full Cycle
An obstruction in the drain line may cause the dishwasher to continue running even after the cycle is finished. The best way to stop the wash cycle is to unplug and troubleshoot the appliance.
To troubleshoot this issue, follow these steps:
1. Turn off the power and remove the access panel.
2. Look into the drain tube using a flashlight.
3. If there are obstructions, remove them.
4. Use a pair of wire-nosed pliers.
Check These Elements And Parts If Ge Dishwasher No Power
If it turns out that these nine reasons are also not what happened to your unit, hold on a little longer because we will try to give suggestions to examine some of the elements and interiors of this unit.
Before we begin, we hope you first turn off all electricity to the unit. The goal is that when inspecting elements and parts, there is no additional risk. If so, proceed with checking in some parts of this dishwasher:
Don’t Miss: Kitchenaid Dishwasher Won T Turn On
Ge Dishwasher Won T Start
If youre like most people, you probably dont think about how to start a GE dishwasher. You just do it. But what if youre not sure how to start your dishwasher? What if something goes wrong and you dont know how to fix it? Dont worry were here to help! check out this article, we will walk you through the step-by-step process of starting a GE dishwasher.
Damaged Dishwasher Main Control Board
If youve used all the approaches above and your dishwasher still doesnt work, it is possible that youve got a damaged control board. If this is the case, the appliance will only work after youve bought a new board. The replacement process for these boards isnt always easy, so you should make sure its something you can do before you embark on it.
You May Like: Can Hydroflask Go In The Dishwasher
Ge Dishwasher Not Starting Orange Light Blinking
One of the most common reasons for an orange light blinking on a GE dishwasher is that the door is not fully closed. This can be easily fixed by opening and closing the door until it latch clicks into place.
Another common cause of an orange light blinking on a GE dishwasher is that something is blocking the detergent dispenser. This can be easily fixed by removing the obstruction and then restarting the dishwasher.
If neither of these solutions work, then the most likely cause is a faulty door switch. This can be easily fixed by replacing the door switch.
Check The Main Board Service Light
A service LED is typically added to GE dishwashers main board to aid diagnostics.
Thus, a good way of checking if the board is receiving voltage is by accessing the main board and checking the status of the service LED.
Now, if the LED is OFF , it means the unit is probably not powered so you should try the following steps:
The main control board should be replaced if improper voltage was found.
Reminder:The seller will be reaching out to ask for the model # before sending it so be sure to double-check your dishwasher model number .
Don’t Miss: Why Is My Ge Dishwasher Not Draining
Ge Dishwasher No Power How To Fix Quick 2022
SteveHey there! Some links on this page are affiliate links which means that, if you choose to make a purchase, I may earn a small commission at no extra cost to you. I greatly appreciate your support!
If your GE dishwasher isnt turning on, youre likely wondering what the problem could be. Is it a fuse? A circuit breaker? Something else entirely? In this troubleshooting guide, well walk you through the most common causes of this issue so that you can get your dishwasher running again in no time!
Do Not Hesitate To Call In A Professional

If youve done your best to bring back the lights to your control panel with no success, you should call in a professional. Go for experts that are known to repair your dishwasher model. If your dishwasher is still within its warranty period, you may be able to get your dealer to send a technician to your home.
Recommended Reading: Best Eco Friendly Dishwasher Detergent
How To Fix A Ge Dishwasher That Wont Start
GE makes a great range of dishwashers, but that doesnt mean they dont break down from time to time. One of the most common problems people have with their GE dishwashers is when they wont start.
If this is happening with your GE dishwasher, follow the steps in this guide to find the cause of the problem and fix it. Please note that you will need to have a multimeter to carry out the majority of these steps if you dont have one or dont know how to use one, youll need to get a qualified technician to come and inspect your dishwasher.
This guide covers most GE dishwasher models, including:
DDW550B-45
WD26X10016
Ge Dishwasher Not Starting Wash Cycle
Here are some possible causes and how to fix them.
If your GE dishwasher doesnt seem to be starting the wash cycle, there could be a few different reasons why. First, check to make sure that the dishwasher is properly plugged in and that the power source is working. If thats not the problem, then it could be an issue with the dishwashers door latch. Try opening and closing the dishwasher door to make sure that its properly latched.
If neither of those solutions seem to be working, then there could be a problem with the dishwashers control panel. If the control panel isnt working properly, you may need to replace it.
Don’t Miss: Bosch 800 Dishwasher Panel Ready
Running An Operation Check
You can run a door status check to see if the latch is the issue. Hold down the select cycle and start buttons at the same time for five seconds. The dishwasher will go through a door status check for 10 seconds after that. A closed-door will show solid LED lights. An open door, or a problem with the latch, will show up as flashing LED lights.
The LED lights will cut off after the door status check, except for the lock LED. This is when you want to run an operations check that runs through the workings of the drain pump, the water valve, the circulation pump, the heater, and the detergent solenoid.
You will start this test while the lock LED is lit. Hold down the select cycle for five seconds. Then, press it again to the selects/increments test. Press start to start the test. You can also press
start to stop it if you need to do so.
Do Ge Dishwashers Have A Lot Of Problems
GE dishwashers dont have a lot of problems and their problems arent any more frequent or severe than other brands. GE is a reliable company.
The most common problems GE dishwashers have are water filling issues, water leaks, draining problems, and the appliance suddenly stopping during a wash cycle.
There are also cleaning issues which means the drain can get clogged. However, you are supposed to clean your dishwasher twice a year to prevent that.
You May Like: Replace Heating Element In Dishwasher
Don’t Miss: How To Unclog Dishwasher Drain Hose