Friday, September 29, 2023
HomeWaterMaytag Dishwasher Not Filling With Water

Maytag Dishwasher Not Filling With Water

Defective Water Inlet Valve

Whirlpool : Maytag :Amana Dishwasher not filling with water diagnostics

When you turn on the faucet, water flows out of the spigot and into your dishwasher through an inlet valve.

If this valve fails or is clogged, then the water will not enter the dishwasher and it will not get cleaned.

Because this is merely a replacement part, there are no services one can provide to fix this component if it is defective.

Is The Water Inlet Valve To Blame

One common reason for a Whirlpool washer not filling with water is that the water inlet valve is not open or is clogged. The water inlet valve supplies water to the washer, and if its not open or does not supply enough water, your Whirlpool washer will not fill up. To check if the water inlet valve is to blame, locate it first. It is usually located on the back of the washer near the water hose connections. Once youve found it, check to see if there is any debris or mineral build-up around it that could be preventing it from opening or closing correctly. If there is, simply clean it off and try again. If this doesnt seem to be the issue, you may need to replace the water inlet valve entirely.

Connect With An Appliance Repair Tech

No in-home service calls. No appointments.

  • However, if you find that the fault is inside your home , you will need to troubleshoot for plumbing problems causing the water not to flow to where its needed.
  • If you cant locate the problem yourself, then it might be best to call a qualified plumber for help instead.

You May Like: My Dishwasher Doesn T Clean Well

Guilty As Charged: The Water Inlet Valve

Repair professionals understand that just a few components are responsible for most appliance problems.

With dishwashers, the water inlet valve is always a prime suspect. When your dishwasher goes rogue, expect to find the inlet valve in the subsequent police lineup.

Signs pointing to a faulty inlet valve include:

  • Leaks that fill the dishwasher when its off.
  • Inadequate water for a cycle. The dishwasher fills too slowly or not all.
  • A bad inlet valve can lead to leaks from the dishwasher onto the kitchen floor. This is potentially hazardous.
  • Most inlet valve malfunctions stem from a defective seal or solenoid failure.

The Float Switch Might Be Faulty

Maytag Dishwasher Troubleshooting No Water : Maytag Dishwasher Not ...

If the float assembly is fine, the problem might be the float switch. When your dishwasher has the correct volume of water, the float lifts and the switch is activated to stop more water from coming into the dishwasher. If the switch becomes faulty, your dishwasher will not fill up with the correct volume of water.

Heres how to check the float switch:

  • Turn the dishwasher off at the wall or turn the circuit breaker off.
  • Open the dishwasher door and remove the lower dishrack.
  • Locate the float switch. Youll need to remove the kickplate at the bottom of your dishwasher.
  • Once located, remove the switch from your dishwasher.
  • Once removed, use a multimeter to check the switch for continuity.
  • If the switch fails the continuity test, you will need to install a new switch. If the switch is working correctly, put it back into the dishwasher and then move on to checking the next possible cause.
  • If you replace the float switch, youll need to turn your dishwasher on and check if the dishwasher now fills with water. If not, move on to checking the next possible cause.
  • Don’t Miss: Stainless Steel Built In Dishwasher

    Damaged Water Inlet Valve

    Your Maytag washer has a component known as the water inlet valve that is responsible for controlling how much water is let into the machine.

    You may locate it on the back of your dishwasher, where there are ports that link to the water inlet hose that was discussed earlier.

    Additionally, as was indicated previously, many models of Maytag washers are capable of receiving both hot and cold water supply simultaneously.

    On these models, the water inlet hoses from both sides of the washer will connect to the same water inlet valve that is located on the back of the washer.

    Before beginning the washing cycle, the water inlet valve must first be opened, which enables water to begin filling up the drum.

    The inlet valve will close as soon as the appliance detects that there is sufficient water in the drum, which will stop any additional water from being poured in.

    In order for the water intake valve to function properly, the water that is being introduced into the system must have the appropriate pressure.

    Therefore, the first possible explanation for why your Maytag washer isnt filling is that the water pressure isnt high enough.

    In addition to that, there is also the possibility that the screens in the water entry valve are clogged with debris.

    These little screens are constructed right into the valve so that any debris or foreign particles in the water. It can be filtered out before they have a chance to become trapped in the washer.

    Solution

    Determine The Connection Type

    Now, examine the valves connections. Youll find two male spade terminals or two small pins.

    • With male spade terminals, you can directly connect your test cord or pack.
    • With pins, you should cut the wiring harness a few inches from the valve. Strip the ends of all four wires. On one side, crimp two male spade terminals, and on the other, two female spade terminals. This ensures you can test power to the valve and quickly reconnect it to the dishwasher after the test.

    Turn on the water supply. Does water leak from the valve even when the dishwasher is without power? If so, replace the water inlet valve immediately. If not, move on to the next step.

    You May Like: Can You Use Dishwashing Liquid In Dishwasher

    Drain Valve And Solenoid Problems

    There is a drain valve within your dishwasher that functions as the hole through which the water is supposed to flow out.

    Should the valve be clogged, it wouldnt be able to properly shake off whatever particles are stuck on it, and in turn, it wont let the water leave your dishwasher.

    You should then check if theres anything in your dishwashers drain tube or pipe because you could have other problems aside from a faulty drain solenoid.

    If you cant seem to find anything after thoroughly checking your pipe and running some unclogging liquid down it.

    Then perhaps one of many other parts within your machine could be causing the problem and not just the drain solenoid.

    Reason #3 Drain Solenoid Malfunctions

    Maytag Dishwasher repair not filling with water

    The drain solenoid is a dishwasher component responsible for draining excess water from the appliance. If it activates too quickly or is malfunctioning, the float switch activation can be triggered, resulting in a dishwasher not filling with enough water.

    To check the performance of the solenoid, access and listen to the drain valve at the start of the wash cycle. If the solenoid is broken or malfunctioning, you will either hear water drain out as fast as it flows in, or hear it trigger the float and not hear water flowing into the tub, you have no other choice but to replace it.

    Read Also: Universal Dishwasher Racks Home Depot

    Is Low Water Pressure In Your House To Blame

    If you have low water pressure in your house, this could be why your Whirlpool washer not filling with water has become a problem. The Whirlpool washer water inlet valve requires at least 20 psi of water pressure to function correctly anything lower, and the washer will not fill.

    To test your homes water pressure, youll need a water pressure gauge. These can be found at most hardware stores. Attach the gauge to an outdoor faucet and turn it on. The reading on the gauge will tell you what your water pressure is. If its below 20 psi, youll need to increase your homes water pressure before your Whirlpool washer works properly again.

    If youve tried all of the troubleshooting steps above and your Whirlpool washer isnt filling with water, its time to call in a professional. Whirlpool washer repair is best done by someone who knows what theyre doing and has the proper tools and experience. Trying to fix it yourself could cost you more in the long run. Save yourself the headache and Capital City Appliance Services today! Our professional appliance repair technicians take care of your washer or dryer repair needs.

    Need Help with Your Broken Appliance?

    Reason #4 Water Supply Kinks

    What you thought was a faulty dishwasher not getting water, might not be the appliance at all. Before jumping to conclusions and rushing to get a new one, examine the water supply line that sends a stream of water to the device. It may either be damaged or bent.

    In the case of the latter, you are in the clear straightening the supply line will solve your problem. If the supply line is damaged youll need to fix or replace it. We recommend hiring a technician to handle the process since you will need to reconnect a new supply line to the dishwashing machine as well.

    Read Also: Replacement Parts For Kenmore Dishwasher Model 665

    Water Inlet Hoses Are Blocked

    If the water inlet hoses are properly connected to a working water supply, check each hose for kinks or clogs. These issues can block water flow so that the washer wont start or fill. Gently straighten any kinks, making sure that the hose isnt damaged with cracks or holes. A damaged hose must be replaced.

    If the water inlet hoses arent kinked, a clog may be responsible for your Maytag washer not filling with water. Disconnect each hose from the washer and carefully remove any blockages with pliers or a straightened wire hanger. Check the inlet screens where the hoses connect to the washer and gently remove any debris with an old toothbrush.

    For An Easier & Safer Repair Call West Coast Chief

    Water Is Leaking From My Maytag Dishwasher

    It all sounds like such fun! If you love tinkering with electronics and mechanical stuff, then it may be your idea of a good time to spend a Saturday afternoon on the kitchen floor, surrounded by testing equipment and dishwasher parts.

    Otherwise, abandon the notion of a DIY water inlet valve repair in the interest of saving a few bucks. Call us at West Coast Chief repair instead. Well determine where the problem lies after all, it may not be the dishwasher water inlet valve, or it may be much more than the inlet valve.

    Once we diagnose the malfunction, well offer an affordable solution to meet your budget repair or replacement, depending on the condition and age of your dishwasher. And in most cases, well have your dishwasher running like a champ by the end of our service call.

    Don’t Miss: Ge Dishwasher Stuck On Lock

    Heres Why Your Dishwasher Is Not Filling With Water

    From time to time, a dishwasher can break down and will need to be repaired. One of the most common problems people have with their dishwashers is that they stop filling up with water.

    In this article, we are going to give you step-by-step instructions on how to fix a dishwasher that isnt filling with water. Simply start with step one and work your way down the steps until youve managed to get it working again.

    The Water Inlet Valve Might Be Faulty

    The next component to check is the water inlet valve. The water inlet valve opens up to let the water fill into the dishwasher. When it becomes faulty or the screen inside of it becomes clogged up, it might not be able to open, and your dishwasher wont fill up with water.

    Heres how to check the water inlet valve:

  • Turn the power off to the dishwasher at the wall or turn the circuit breaker off.
  • Locate the water inlet valveit is behind the lower kickplate panel which youll need to remove.
  • Once located, first check that the water hoses are not kinked or blocked in any way. If the hoses are okay, disconnect the water inlet valve.
  • Next, use your multimeter to check the valve for continuity.
  • If the valve fails the continuity test, you will need to install a new one. If the valve is working correctly, put it back into the dishwasher and then move on to checking the next possible cause.
  • If you replace the water inlet valve, youll need to turn your dishwasher on and check if the dishwasher now fills with water. If not, move on to checking the next possible cause.
  • Don’t Miss: Soap Dispenser On Dishwasher Not Opening

    Water Level Pressure Switch Is Defective

    A Maytag washer water level sensor responds to the washers water levels, signaling the water inlet valve to open or close. If the sensor malfunctions, it wont signal the valve for water to start a cycle and the washer wont fill. It may also result in the washing machine stopping mid-cycle and failing to advance to the next function.

    To determine if the sensor is defective, it should be assessed for damage and continuity. However, it can be difficult to access below the control panel or sump area underneath the washer tub. We suggest that a professional service assess and replace the sensor, if necessary.

    The professionals at Service Care can perform any Maytag washer repair to restore proper function. Call us for all your laundry appliance needs!

    Toxey McDavid

    The Float Assembly Might Be Defective

    Dishwasher will not fill with water – Diagnostic & Repair -Whirlpool, Maytag, KitchenAid & Roper

    The best place to start is to check the float assembly. When the water is filling into your dishwasher, there is a float that rises to ensure the right amount of water fills into your dishwasher. If it becomes defective or gets out of place it might prevent your dishwasher from filling up.

    To check the float assembly, you need to:

  • Turn the dishwasher off at the wall or turn the circuit breaker off.
  • Open the dishwasher door and remove the lower dishrack.
  • Locate the float assembly. It can be found inside the dishwasher in the tub.
  • If the float assembly has a cover over it, remove it.
  • Once youve located the float assembly, pull it up and let it go to see if it can move without obstruction. If it moves freely, it is probably not the cause of the problem, so you can move on to checking the next possible cause.
  • Next, remove the float and then check for any loose debris that might be obstructing it. If you find any obstructions, remove them and then put the float back in.
  • Once the float is back in and the cover is on it, turn your dishwasher on and check if it now fills. If not, move on to checking the float switch .
  • Read Also: Ge Profile Dishwasher Parts List

    How To Troubleshoot A Maytag Dishwasher Not Filling With Water

    Before you call to have your Maytag dishwasher serviced because it does not fill with water, go through a few troubleshooting steps first to narrow down the problem. In some situations, you may be able to find the problem and fix it without a costly repair. When troubleshooting your dishwasher — or any mechanical device, for that matter — use the line of reasoning attributed to 14th century Franciscan friar and logician William of Ockham. The principle, commonly known as Ockham’s razor, suggests that the simplest answer is often the correct one.

    Fix Appliances Ca Skilled Professionals For Dishwasher Repair

    Identifying the root cause of a dishwasher not filling with water is not easy if you dont have a trained eye for it. Thats why you can only be fully confident in the appliances performance after a professional team takes a look at it.

    To correctly identify why a dishwasher is getting no water and repair malfunctions, hire technicians from FIX Appliances CA. We are a Canadian certified service repair contractor.

    Thousands of homeowners in Ontario and elsewhere trust FIX Appliances CA as their leading dishwasher repair team heres why:

    To get a free service call from FIX Appliances CA technicians, reach out to our team. You can either leave us a message or call 1-888-242-077. We look forward to hearing from you and helping you improve the efficiency of every appliance at your home or business.

    Discount Coupon

    Also Check: Samsung Dishwasher Side Mounting Bracket

    Is The Washer Fill Hose Causing Issues

    Another common reason why your Whirlpool washer not filling with water is because of a kinked or twisted washer fill hose. The washer fill hose carries water from the water inlet valve to the washer tub, and if its kinked, water will not be able to flow through properly. Simply locate the washer fill hose and straighten it out to fix this. If there doesnt seem to be any kinks or twists, then check to see if the hose is clogged with debris. If it is, clean it out and try again.

    Reason #2 Dirt On Valve Screens

    Filling the Dishwasher Water Softener

    To get into the dishwasher, water passes through inlet valves. If the stream of water is weak, unevenly distributed, or absent altogether, its likely that dirt and debris have clogged the filler valve screen filters.

    Disassembling a portable dishwasher and cleaning the inlet screen will, in most cases, solve the problem. However, if the valve screen is damaged, you need to replace it.

    Don’t Miss: Bosch Silence Plus 44 Dba Dishwasher

    Action #2 Assess The State Of The Float

    To fix a problem when a dishwasher wont fill with water, you need to make sure that the float switch is on only when the water level reaches its peak height. As a way of fixing water supply issues, access, and evaluate the performance of the float valve following the steps below.

    • Disconnect the dishwasher from the power source.
    • Remove the cover protecting the float assembly inside of the washer. Slightly lift the float to see if it can drop on its own. If so, theres nothing wrong with it. If not, remove the float, inspect it for debris and damage, clean and replace the component.
    • Detach the access panel from the dishwasher to make sure the float interacts with the float switch smoothly.

    RELATED ARTICLES

    Most Popular