Jenn Air Dishwasher Control Panel

Jenn Air Dishwasher Leaks

Diagnose the problem with your dishwasher door gasket by finding its cracks or holes, along with checking for splits and tears in the seal that your arm inserted through during the drop test.

Another telltale sign of a problem with the dishwasher door gasket is visible watermarks, which result when this part fails to hold back any amount of liquid from seeping out.

Make sure to identify issues within the joints of your dishwasher door gasket, or else it might not form a good airtight seal around your appliances hinges.

If you find that one or more areas associated with this part require an adjustment, it may be time to replace it entirely.

The Dishwasher Does Not Dry Dishes

We find that the most common cause for water lines is faulty venting. Now, lets explain how we know this to be the issue.

The main purpose of the ventilation system in your dishwasher is to clear out excess steam from the wash cycle.

After all, there arent many appliances that can withstand having extra hot water dumped on them.

As such, if theyre unable to get rid of said steam fast enough, it has no place to go other than back on your dishes.

Next, Use a multimeter to test the continuity of the heating element in order to determine if it is burnt out. If the heating element is not continuous, replace it.

Find Similar Products By Category

Don’t Miss: Bosch 800 Series Dishwasher In Stock

Using The Control Lock On Your Jenn

The control lock on a dishwasher is intended to “lock” the control from unintended use. It can be used while the dishwasher is operating or not. This is perfect for the household with children who like to touch buttons so the dishwasher cannot be turned on accidently or turned off when running.

NOTE: You must press the actual button to activate Control Lock, not the words that say “Hold 3 sec”.

Is The Control Lock Option Activated

Control Lock is used to avoid unintended use of the dishwasher between cycles, or cycle and option changes during a cycle. The red lock indicator shows that the control lock is activated, and the control panel cannot be used while this is activated.

To turn off Control Lock, press and hold the button designated for your model for 3 seconds. This will vary depending on your model number. Once held for 3 seconds, the lock indicator light will turn off. See your Owner’s Manual for your specific model.

NOTE: You may need to disable Sleep Mode by pressing either Start/Resume or Cancel, or by opening and closing the door before you are able to turn Control Lock off.

If you would like to download or view product literature for your appliance, please visit our Manuals and Literature page.

You May Like: Bosch Dishwasher Models By Year

Flashing Or Blinking Dishwasher Lights

The heating element is what heats up the water, An LED indicator light may flash if the water has not reached the proper temperature.

To determine if the heating element needs replacing, it must be tested using a multimeter to see if it still has continuity.

If this test is negative, the part should be replaced immediately.

Has A Delay Wash Option Been Selected

A delay wash option runs the dishwasher at a later time or during off-peak electrical hours. If the delay wash has been selected, the dishwasher will not run until the delay time is reached.

To Turn Off the Delay Wash Feature:

Don’t Miss: Kitchen Aid Dishwasher Parts List

How To Set The Control Lock:

If the Control Lock feature has been enabled, the Control Lock light will flash 3 times indicating that it is activated. Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.

If the dishwasher has a dedicated Control Lock button in the Options selections, press and hold CONTROL LOCK for 3 seconds .

NOTE: You may need to disable Sleep Mode by pressing either Start/Resume or Cancel, or by opening and closing the door before you are able to turn Control Lock off.

NOTE: If your model requires you to press and hold PROSCRUB UPPER, 4 HOUR DELAY, SANI RINSE, or BOTTLE WASH to lock the controls, the Control Lock light will be on when Control Lock is active.

If you have further questions about the control lock on your model, please see your Owner’s Manual.

If you would like to download or view product literature for your appliance, please visit our Manuals and Literature page.

How To Reset The Dishwasher:

Much like a computer, resetting the dishwasher control can sometimes solve the issues you are experiencing. To reset the dishwasher control panel, it needs to be disconnected from the power source for one minute. If your dishwasher is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in. If the dishwasher is hard wired to the power supply, turn the breaker off at the home electrical panel that powers the dishwasher for one minute and then turn the breaker back on.

Also Check: Ge Dishwasher Heated Dry Not Working

Is The Control Lock On

The control lock is used to avoid unintended use of the dishwasher as well as to avoid unintended cycle or option changes during a cycle. The control lock light will stay on for a short time, indicating that it is activated and all buttons are disabled. If any buttons are pressed while the dishwasher control is locked, the light will flash three times. The door can still be opened/closed while the controls are locked.

Some models have an indicator light for the Control Lock. This may be located on another button, or it may be a button itself, depending on your model. This may be red or green, and appears to be a small padlock. If it is located on another button, you will typically have to press and hold that button for 3 seconds. See image below:

NOTE: To enable or disable the Control Lock, you must touch the actual button, not the words “Hold 3 sec” below the button. This is the same regardless of your model having a separate Control Lock button, or if it is located on another button . .

See the Owner’s Manual for your model to determine how to enable and disable the Control Lock for your Dishwasher.

NOTE: You may need to disable Sleep Mode by pressing either START/RESUME or CANCEL, or by opening and closing the door before you are able to turn the control lock off.

To turn off the control lock feature:

The Dishwasher Dispenser Does Not Dispense Soap

The bi-metal actuator is a latch that will release the detergent dispenser door by acting on electricity. It will not release the dispenser door if the bi-metal is burned out.

A multimeter can be used to determine if the bi-metal is still functional. If there is no continuity, it needs to be replaced.

Make sure that the dishwasher itself is getting enough water since this might keep your mechanics from working properly.

Inspect for damage in replacing parts for your dishwasher especially when those faulty parts happen to be the Detergent Dispenser.

Related Guides

Read Also: What Is An Ada Dishwasher

Trouble Starting Jenn Air Dishwasher

Leaving the door open prevents the dishwasher from starting. To determine if the faulty switch is causing this issue.

Plug your multimeter into its low voltage setting and then use it to test for continuity between either side of the door switch.

If either side of the switch has continuity through it , then you should replace the bad part with a new one because this means the door is not closing properly.

The wiring in both instances must match or else they will not work properly.

Jenn Air Dishwasher Control Board

Electronic control board

Order by 8:00 PM ET, this part ships TODAY!

Electronic Control Board

Electronic control. NOTE: This part is often misdiagnosed. Enter your Dishwasher model# into our repair help section for additional repair help.

OEM Part – Manufacturer #12002710

Order by 8:00 PM ET, this part ships TODAY!

Electronic control board. NOTE: This part is often misdiagnosed. Please enter your dishwasher model# into our Repair Help section for additional repair help.

OEM Part – Manufacturer #12002709

Timers and control boards are often incorrectly diagnosed as the problem. If you are not sure this part is defective then we suggest checking out our Repair Help for additional information.

Recommended Reading: Bosch Silenceplus 44 Dba Dishwasher

The Jenn Air Dishwashers Buttons Arent Working

First, ensure that the display is synced correctly with the touchscreen functionality.

If the display is working properly but the touchpad on your control panel isnt functioning correctly, it may be a good idea to replace just that part.

Its important to remember however that some appliance companies only sell their touchpads as a set and if this is the case then you will need to replace them together.

To Reset The Dishwasher Control Panel:

If your dishwasher is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in. If the dishwasher is hard wired to the power supply, turn the breaker off at the home electrical panel that powers the dishwasher for one minute and then turn the breaker back on.

NOTE: If you dishwasher appears to have no power, no lights, etc. please verify that the Control Lock has not been activated. If the Control Lock is set, your control will not operate at all, and a red “Padlock” may be illuminated. Check the Owner’s Manual for your model dishwasher to learn how to de-activate the Control Lock.

for more information about the Control Lock on most dishwashers

If you would like to download or view product literature for your appliance, please visit our Manuals and Literature page.

Also Check: What Causes Dishwasher Not To Drain

Jenn Air Diswasher Mod # Jdb1100aws

DISHWASHER WILL NOT WORK .NO LIGHTS ON CONTROL PANEL ATTEMPTED A RESET VIA THE CIRCUT BREAKER,I CYCLED THE POWER GOT LIGHTS TO COME FOR NORMAL WASH AND HEAT DRY BUT THE UNIT WILL STILL NOT WORK .AFTER A FEW MINUTES THE LIGHTS SHUT OFF. DO YOU THINK I SHOULD REPLACE THE CONTROL BOARD?

Posted byCHEVPALAon

• An expert who has achieved level 1.

  New Friend:

  An expert that has 1 follower.

• Contributor
• 1 Answer

Has anyone got asolution to this? I have the jdb1270 and am experiencing the same thing. 2 years later. Looks like Jenn-air has not fixed this problem

Posted on Nov 17, 2010

Cycle Power To The Control To Reset The Dishwasher:

Much like a computer, resetting the dishwasher control can sometimes solve the issues you are experiencing. To reset the dishwasher control panel, it needs to be disconnected from the power source for one minute. If your dishwasher is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off at the home electrical panel that powers the dishwasher for one minute and then turn the breaker back on.

Also Check: Where To Put Detergent In Dishwasher

What Customers Are Saying:

Thank you for the expeditious answer. It’s good to know you’re out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air.

JeanRiverhead, NY

You did one super job of explaining to me everything there is to know about this fridge. I’m looking forward to asking you questions in the future.

JimmyBagley, IA

Wonderful service, prompt, efficient, and accurate. Couldn’t have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn’t be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Jenn Air Dishwasher Troubleshooting

Certain steps may need to be repeated if the machine does not complete a cycle. Cycle and see if there is any obstruction in the lint trap.

The drain might not be clear or the water heater might not be working.

Stuck dishware may be due to improper loading of cups and glasses against the rotation arm.

Make sure there is plenty of space between each item as too much contact while in motion can cause a jam.

Also Check: Dishwashers On Sale Stainless Steel

Jenn Air Dishwashers Do Not Clean

Water enters the dishwasher through the water inlet valve. The dishwasher will not be able to clean dishes properly if the inlet valve is clogged or defective.

Inlet valves that are stuck need to be replaced. You may worsen the problem by attempting to clean or repair the inlet stem. As a result of the dishwashers wash impeller, water is sprayed onto the dishes.

If either of these parts begins to fail, youll be dealing with an expensive repair bill consider upgrading these components before it gets too bad.