What To Do After Resetting The Dishwasher
Resetting the dishwasher takes somewhere around 10 to 15 minutes. After this, you check the configuration of the dishwasher.
There are lots of things that you can check on your dishwasher. The first one is to check the water pressure and temperature of the water.
Besides this, check if the sensor has moisture or not. If there is moisture, give some time to dry otherwise, this same problem could omit error codes.
You can also check the drainage pipe, clean the dispenser with water, and fill in new detergent.
Clean Out Filters Regularly
Sometimes there might be too much dirt or leftover food in the filter. If this happens, remove them immediately and clean all parts of the washer thoroughly with a damp towel.
Always read the instructions provided by manufacturers before trying to clean any part of your appliance. Otherwise, you may break it or cause some other serious damage.
Check The Drain For Clogs
Dishwasher drains can become clogged. Many homes have the dishwasher set up to drain in the same space as the garbage disposal. This overlap means that a clog in the garbage disposal can also impact the dishwasher drain line and cause standing water to accumulate in the appliance.
If you believe there is a clog, you can check the dishwasher drain hose by following these steps:
- Carefully disconnect the drain hose from where it connects to the garbage disposal or sink.
- Put one end into a bucket to avoid a mess.
- Once you have one end safely in a bucket, fill the dishwasher and drain it.
- Watch the water as it comes out.
- In some situations, this will encourage the clog to come out on its own.
- Reattach your hose and run the appliance normally.
If the water trickles out, you might have a clog thats not easily dislodged. In this situation, carefully pull the dishwasher out from the wall so you can disconnect the drain hose completely.
Remember that water will likely leak from the appliance when you do this. Put a pan underneath to prevent water from getting on the floor. Once disconnected, youll be able to tell if the clog is one you can reach to clean out. You might have to replace the hose if it is damaged.
Don’t Miss: Jenn Air Dishwasher Control Panel
Try To Activate Diagnostic Mode
If your dishwasher has a flashing light or an alarm has sounded, this can sometimes be fixed by resetting your dishwasher.
If you dont have a reset button, you can try the following to reset your dishwasher:
Does It Matter How You Load A Dishwasher

Learning how to load a Whirlpool dishwasher not only results in cleaner dishes but saves time and energy. Separating and positioning items correctly and using racks and slots properly ensures that water, detergent, and air can reach every item. This translates to clean, dry dishes with every wash load and prevents breakage and dishwasher malfunctions. Proper loading also saves water, energy, and time that gets wasted with re-washing and drying.
Also Check: Does Lowe’s Install Dishwashers
Try To Reset The Control Board
The next step is to reset the control board. The control board can become faulty and stop your dishwasher from working properly, especially if there has been a power outage or surge. Sometimes, a simple reset of the control board will solve whatever problems youre having with your Whirlpool dishwasher.
Heres how to reset the control board:
Check Whether The Wash Cycle Is Complete
To begin, make sure that the dishwasher has completed its cycle. If you accidentally open the dishwasher before it finishes the cycle, you might find it filled with water.
Before you do anything else, look at the indicators on your dishwasher to see if a light or notch properly indicates the clean or off option. If you do not see this light, you might have accidentally interrupted the cycle. Simply close the door and press the start button again to tell the appliance to finish its cycle.
Read Also: Bosch 500 Vs 800 Dishwasher
When To Clean The Dishwasher Filter
Newer dishwashers with manual-clean filters should be cleaned about once a month. Keep an eye on your dishes after you run a cycle: if they still have food stuck on them, or if they have a gritty feel, your filter is likely due for a cleaning. Also watch for odors from your dishwasher, which indicates you need to clean your filter more often.
Quick Whirlpool Dishwasher Reset Methods
The downside to Whirlpool appliances is that they dont have a reset button. But some of them do have certain error codes. You can identify them from the user manual.
If you cant identify the error code, lets start with the most basic step. Simply disconnect your dishwasher from the power source and leave it for one minute. After a minute, you reconnect it and turn on your dishwasher.
If your dishwasher is hard-wired, simply turn off the breaker its connected to. After one minute, turn the breaker back on and see if your dishwasher works properly or not. The breaker is located inside the circuit box of your house, in case you have no clue about it.
If this doesnt fix your dishwasher, keep reading. If it does, you can still read this guide till the end, in case your dishwasher decides to give you trouble again.
You May Like: Bosch 800 Series Dishwasher Installation
The Dishwasher Smells Bad Or Is Leaking
Its easy to understand why a smelly dishwasher would turn people off. A smelly appliance can result from food remaining on dishes, not using the hot water setting, or not running it enough.
You can help eliminate odors by always using the hottest water possible and by regularly running the dishwasher on heated dry without any dishes inside.
Load Whirlpool Dishwasher Racks
1. Cutlery rack
The third rack was designed to house the cutlery. Arrange the cutlery, A separate arrangement of the cutlery makes collection easier after washing and improves washing and drying performance.
Knives and other utensils with sharp edges must be positioned with the blades facing downwards.
The geometry of the rack makes it possible to place such small items as coffee cups in the area in the middle.
The cutlery basket is equipped with two sliding side trays to make the most of the height of the space below and enable the loading of high items into the upper rack.
2. Upper rack
Load delicate and light dishes:- glasses, cups, saucers, low salad bowls.
The upper rack has tip-up supports which can be used in a vertical position when arranging tea/ dessert saucers or in a lower position to load bowls and food containers.
Foldable flaps with adjustable position:
The side foldable flaps can be positioned at three different heights to optimize the arrangement of crockery inside the rack.
glasses can be placed safely in the foldable flaps by inserting the stem of each glass into the corresponding slots.
For optimum drying results incline the foldable flaps more, To change the inclination:
- Pull up the foldable flap.
- Slide it slightly and position it as you wish.
Adjusting the height of the upper rack:
To restore to the lower position, press the levers at the sides of the rack and move the basket downwards.
NEVER raise or lower the basket on one side only.
3. Lower rack
Also Check: Bosch Dishwasher Replace Drain Pump
What To Do Before Loading A Dishwasher
Knowing how to load a Whirlpool dishwasher actually starts before a single dish is loaded. Just a few key interventions can make a difference in how your dishwasher functions.
These dishwasher pre-loading tips can result in cleaner dishes:
- Skip the pre-rinse: Most dishwasher detergents work better with a little grease and grime. Just scrape off large food particles before loading.
- Avoid overloading: Wondering how not to load a dishwasher? Overloading is a common mistake. It limits access to detergent and water as well as the airflow needed to dry dishes.
- Always use a rinse aid: Not only will dishes sparkle, but water droplets will disperse more easily, resulting in improved drying.
Why Whirlpool Dishwasher Not Drying

There are a few reasons why your Whirlpool dishwasher may not be drying your dishes properly. First, check to make sure that the dishwasher is correctly loaded and that there is nothing blocking the spray arm. Next, ensure that the rinse aid dispenser is filled and that the correct amount of detergent is being used. Finally, run the dishwasher through a cleaning cycle to remove any built up food or grease that may be causing the issue. If the problem persists, then it is likely that there is a problem with the dishwasher itself and you should contact a qualified technician for assistance.
Don’t Miss: How To Turn On Ge Dishwasher
How To Load The Upper Rack In A Whirlpool Dishwasher
A Whirlpool dishwashers upper rack holds small bowls, plates, cups, and glasses. Adjustable tines and stemware holders can be folded down to accommodate different shapes and sizes or to safely secure wine glasses. The upper rack also keeps glassware and smaller items separated, reserving the lower rack for larger pieces.
These upper rack loading suggestions can improve dishwasher performance:
- How to load bowls in a dishwasher: Place them upside down and at an angle for better access to water and detergent.
- How to load glasses: Position glasses and cups upside down and angled to access spray arms and improve drying.
- Reserve for plastic and large utensils: The upper rack keeps plastic away from the dishwashers heating element below and prevents longer utensils from blocking the spray arms.
Why Does My Whirlpool Dishwasher Smell Bad
Dishwashers do an excellent job of cleaning dishes. However, the food particles stuck to the plates, bowls, pots and pans still end up somewhere. These little pieces of food can get lodged inside the dishwasher if you dont clean out your appliance regularly. Over time, this food can begin to rot and grow bacteria, leading to a bad smell coming from your dishwasher.
The best way to solve this problem is to give your dishwasher a good cleaning. Remove the bottom dish rack and clean out any food buildup trapped along the bottom or sides.
You can also look at your manufacturers instructions to see how to use a screwdriver to uncover the dishwasher filters and clean them. Before taking the filters out, ensure you understand the filter assembly so you can put them back together. Getting rid of this grime can help eliminate foul odors.
Recommended Reading: Sink Backs Up When Dishwasher Runs
The Dishes Arent Getting Clean
Make sure you use enough dish detergent. Most people dont use nearly enough and then wonder why their dishes dont get clean. You should be using one tablespoon of powdered or liquid soap or two teaspoons of gel per load. Another alternative is to use dishwasher pods to avoid miscalculating measurements.
If your dishwasher has an automatic dispenser, make sure you have it set to normal. Automatic dispensers can be adjusted so that they use less soap. If you choose automatic with a low wash, the dishes will not get nearly as clean because there isnt enough soap being used.
Load The Right Type Of Dishes Inside Of The Washer
Some kinds of materials require special attention when cleaning them with hot water. For example, if you wash regular plates made out of ceramic or glassware in hot water, they may crack.
The same goes for some types of plastics because their material composition has changed slightly since being created, so they cannot withstand high temperatures anymore dont forget that when you are loading your dishwasher.
Recommended Reading: Can You Use Affresh Dishwasher Cleaner In Washing Machine
How To Keep My Whirlpool Dishwasher From Malfunctioning
Like any electrical appliance in your house, your dishwasher needs care. This includes keeping it clean and following all of the maintenance guidelines provided in its manual.
With your Whirlpool dishwasher, here are the steps you should follow regularly:
- Clean the filter regularly. It accumulates food scraps and can get clogged very easily, causing the dishwasher to malfunction.
- Check the inlet temperature of the water in your dishwasher. Whirlpool recommends that it should be between 50 to 60 degrees Fahrenheit.
- If your dishwasher has a rinse aid, always check its level. It shouldnt decrease too much.
- Install surge protection for your Whirlpool dishwasher. This helps avoid malfunctions caused by electrical outages or power surges.
Do Not Overload The Washer
Simply put, do not put too many dirty dishes inside of your dishwasher. Remember that the whole point of using a dishwasher is to help you clean the kitchen faster and easier.
If you overload your machine with dishes, it will not be able to finish its work properly and that would be extremely frustrating.
Recommended Reading: Whirlpool Dishwasher Wdt 730 Pahz
Features On Whirlpool Dishwashers
Whirlpool dishwashers come with various features that make them more user-friendly and effective. Here are some of the most popular ones:
- Sanitize Cycle: The sanitize cycle on Whirlpool dishwashers is ideal for cleaning baby bottles, glasses, and dishes that need to be extra clean. This cycle uses hot water to kill 99.999% of bacteria and germs, so you can be sure that your dishes are safe to use.
- Soak Cycle: The soak cycle is perfect for heavily soiled or greasy dishes. It pre-soaks the dishes in hot water and detergent for a few minutes before the main wash cycle starts, which helps to loosen and remove tough stains.
- Quick Wash Cycle: The quick wash cycle is ideal for lightly soiled dishes that need to be cleaned quickly. It uses less water and detergent than the other cycles, and it runs for a shorter period.
- Delay Start: The delay start feature on Whirlpool dishwashers allows you to set the dishwasher to start washing the dishes later. This is perfect if you want the dishwasher to run while you are asleep or out of the house.
- Child Lock: The child lock feature prevents curious little hands from changing the settings on the dishwasher or opening the door while it is running. This is a great safety feature if you have young children.
Now that you know about some of the features that Whirlpool dishwashers offer, lets take a look at how to use them.
Cleaning Your Whirlpool Dishwasher With Vinegar And Baking Soda

Vinegar and baking soda are great for cleaning almost anything in your home. Both are cheap, readily-available, and will kill the bacteria and cut through the dirt.
Watch the video below if you prefer a visual explanation.
Also Check: Smart Linear Wash 39dba Dishwasher
How Much To Fix Whirlpool Dishwasher
This is a difficult question to answer without knowing the specific problem with your dishwasher. However, common repairs for Whirlpool dishwashers can range in price from $100 to $200. If you are having trouble with your dishwasher, we recommend contacting a qualified appliance repair technician for an estimate.
When Using The Dishwasher Follow Basic Precautions Including The Following:
Load your dishwasher with all the dishes facing the spin arm where the water is sprayed from during the wash and rinse cycles. Position large bowls between tines or along the side, back or front of the bottom rack. Tips on using a whirlpool dishwasher such as adding detergent and rinse aid, how the sprayers work and canceling the wash.please subscribe to my channel for.
You May Like: How Do I Fix My Dishwasher Leaking From The Bottom
Consult Your User Manual
If turning the power off and on didnt work, the next step is to find the user manual for your specific model of Whirlpool dishwasher. If you dont have a physical copy, you should be able to find an online version by simply Googling Whirlpool Dishwasher .
Each different model has its own reset instructions, so if you find the user manual, you should check it for how to reset your dishwasher. If you cant find your manual or if the method doesnt work, start going through the next steps in this guide, which will cover all of the most common ways to reset a Whirlpool dishwasher.