Tuesday, December 5, 2023
HomeGEHow To Tell If Ge Dishwasher Control Board Is Bad

How To Tell If Ge Dishwasher Control Board Is Bad

How To Fix The Error Code In The Dishwasher

Diagnose Codes and Replace Repair Bad PCB Control Board in GE Dishwasher

First, you need to identify the exact problem behind the error code to fix the error code.

If you dont have any idea about the error code, you can refer to the owners manual.

You will find a detailed explanation of the error code, solutions, and various tips and tricks there. You should contact your seller if the owners manual solution doesnt work.

Deactivate The Child Lock

To deactivate the control lock on the GE dishwasher, press and hold the Heated dry pad for about 3 seconds. The locks light should go off, indicating that its inactive. It should help, so the buttons and control panel respond to presses.

However, if pressing the corresponding pad doesnt deactivate the control lock, you should reset the unit. Unplug it from a power source, wait at least 60 seconds, and put the machine back on. Repeat the process with the Heated dry pad.

Rebooting The Dishwasher Is An Option

Rebooting a GE dishwasher is a straightforward process. You can disconnect it from the circuit breaker of your house or power source for a few minutes to reboot it.

The control panel might be working again when you reboot the machine.

Make sure to take the proper electrical precautions at this stage to avoid any accidents.

Read Also: My Dishwasher Smells Like Fish

How Do You Reset The Leak Detected On A Ge Dishwasher

The leak detected ge profile dishwasher does not require a reset per se but correction of the leakages. For example, if you reset the appliance and the ge profile dishwasher ld code disappears, the code reappears as soon as you run the cycle since the reset can never solve the leak problem. However, it can still solve the problem if the control board misbehaves.

To reset the leak detected in the ge dishwasher:

  • Turn the power off by unplugging or cutting off the power at the circuit breaker.
  • Leave the appliance disconnected for 5 minutes
  • Press the start button for a few seconds.
  • Wait for the light above the start button to flash.
  • The water pumps out of the tab.

Recommended Reading: How Do I Fix My Dishwasher Leaking From The Bottom

Ge Profile Dishwasher Buttons On The Control Panel Not Working

GE WB23T10023 Touch Control Board (AP3993940)

A GE Profile dishwasher is only as good if it has all the buttons working. So if you notice that some buttons on the control panel arent working, you should do a thorough inspection and fix the problem.

You have two options here.

The first option is to clean the ribbon cable to remove dirt, rust, and grime.

These foreign materials may be causing loose or bad connection between board and the connections on the ribbon cable. As you clean, also check to make sure that the cable has a proper attachment.

The other option is to replace the control panel. You might want to look at the GE WD34X21699 Dishwasher Control Panel if youre looking for a recommendation.

Also Check: Miele Dishwasher With Water Softener

Inspect The Door Latch

When the door latch is not engaged, a switch prevents the dishwasher from starting. Listen for the sound of the latch clicking into place when you close the door. With the door closed, pull on the door to see if it is closed securely. Visually inspect both sides of the latch for anything that may be preventing it from engaging properly, and for broken parts. If the latch is broken, the switch may be also.

Ge Profile Dishwasher Control Panel Locked

The buttons on the GE Profile dishwasher control panel wont work if the Control Lock is on.

We understand how useful the Control Lock feature is. It helps to keep kids from interrupting an ongoing cleaning cycle or starting a new one by accident.

However, having the Control Lock on in a GE Profile dishwasher means that even the control panel wont work.

The solution here is to deactivate the control lock. To do this on a GE Profile dishwasher:

  • Press and hold the Heated Dry pad for 3 seconds.

The locks light should go off, indicating that the control lock is inactive. The buttons in the control panels should respond to presses.

If pressing the Heated Dry pad doesnt deactivate the Control Lock, reset the unit by unplugging it from the power source and waiting for at least 60 seconds before powering the machine back on.

Read Also: Diy Clean Dirty Dishwasher Sign

Make Sure The Door Switch Is Working

The second step is to make sure the door switch is working correctly. The purpose of the door switch is to prevent the door from opening during a wash cycle. Sometimes they can become faulty, and this causes the control panel to believe the door isnt shut properly, which results in the control panel not letting the dishwasher start.

Checking the door switch requires testing it with a multimeter to do that:

  • Switch the power to the dishwasher off at the wall or circuit breaker.
  • Locate the door switch .
  • Depending on your specific make of GE dishwasher, you may need to remove the door switch fully or unplug it before testing it .
  • Use your multimeter to test the door switch for continuity.
  • If the test shows continuity, move on to step 4, as its working correctly. If it doesnt have continuity, it will need to be replaced with a new switch.
  • Once the replacement has been carried out, turn the power back on, and attempt to start your dishwasher. If it still doesnt start, move on to step 4.
  • Damaged Dishwasher Thermal Fuse

    Diagnosing a Bad GE Board – Part 2: Visual Inspectios

    Theres a thermal fuse in your dishwasher that protects it from overheating. When this fuse blows, you wont get any lights on the control panel. Your dishwasher will actually work just fine, but there may be some parts that need maintenance or replacing. Have a specialist check out the situation and make sure your appliance is operating at peak performance.

    If your dishwasher is experiencing an issue that doesnt involve the controls, check for a blown thermal fuse near the control panel first. Its usually a small white or silver cylinder with two wires connected to it. Test this fuse for continuity. This can be done by using any multimeter with a continuity setting.

    Locate the thermal fuse. Its usually next to the control board if the circuit board has been mounted vertically. If the control board has been mounted horizontally, the thermal fuse will be on the right side.

    Its usually located under a translucent cover. Use a flathead screwdriver to gently pry the cover off the fuse. Insert the probes on your multimeter into the two holes on the fuse.

    If the thermal fuse fails the continuity then replace it.

    Recommended Reading: Bosch 500 Vs 800 Dishwasher

    How To Tell Whether The Touchpanel Or Control Board Is Bad In A Whirlpool Dishwasher

    Entry posted by Samurai Appliance Repair Man·July 8, 2013

    Many times when troubleshooting a Whirlpool-built dishwasher , you’ll have a problem that looks like it could be either a bad touchpanel or the control board, but you can’t really be sure. Examples include:

    – Normal light keeps blinking but the dishwasher won’t run

    – none of the lights on the panel work and the dishwasher won’t run

    Could take on lots of other variations but the thing they’ll all have in common is that dishwasher won’t run.

    The conundrum you face is which part to replace: the touchpanel or the control board?

    Experience says that it’s almost always the touchpanel that goes bad in these cases– a keypad gets stuck closed or worn on the inside so it no longer makes contact.

    Fortunately, there’s a way to tell for sure without any guesswork!

    Remove the kickpanels below the door and you’ll find a tech sheet in a plastic pouch . Therein it is written this simple procedure for determining whether the touchpanel or control board is the culprit:

    Check Control Panel Wiring

    About this: If the control panel is still problematic, you should inspect its wiring closely. The wiring is likely loose or damaged, allowing the panel to receive power but not communicate correctly with the main control board.

    As a result, the control panel is on but pushing its buttons doesnt get you the outcome you want.

    What to do: You must reattach all electrical connectors firmly. If there are any damaged wires, you must replace them with new ones.

    Read Also: How To Get Rid Of Black Mold In Dishwasher

    How To Fix A Ge Dishwasher Control Panel Not Working

    When youre sure your GE dishwasher is not working properly, and there is nothing wrong with the soap dispenser, the water valve, or the door seals, but the control panel is not responding, its a mess.

    If the GE dishwasher control panel is not working, it doesnt necessarily mean the whole unit is faulty. As you can see from the seasons weve just discussed, anything could be from a poor power supply to a blown thermal fuse.

    Run through these quick DYI solutions before calling a technician.

    How Do I Know If My Dishwasher Control Panel Is Bad

    GE WH12X10355 Control Board Assembly

    There are a few things you can do to check if your dishwasher control panel is bad. First, try to reset the dishwasher by unplugging it and then plugging it back in. If the dishwasher still doesnt work, you can try to contact your dishwasher manufacturer to see if they have any troubleshooting tips.

    Recommended Reading: What Is Standard Dishwasher Size

    Check The User Interface Control Wiring

    Many dishwashers have a user interface control in the control panel that connects to the electronic control board.

    If the dishwasher still isnt getting power, check the user interface control wire harness. The control panel wont light up if the wire harness is disconnected.

    • Shut off power to the dishwasher.
    • Open the dishwasher door and remove the Torx screws from the outer edges of the inner door panel. So the outer door panel doesnt fall off, support it with one hand as you remove the final screws.
    • Check the wire harness connection between the user interface control and the electronic control board.

    If the user interface control wire harness is unplugged, reconnect it. Reassemble the dishwasher and restore power.

    How Do I Replace My Dishwasher Touchpad Or Control Panel

    If your control panel keys are stuck, or your dishwashercontrol panel problems were unable to be fixed by resetting the control panel,removing a child lock or turning on the power, its possible that yourdishwasher control panel repair will in fact become a replacement. Luckily,replacing the control panel is a relatively simple task.

    You May Like: Whirlpool Stainless Steel Tub Dishwasher

    Why Is My Ge Dishwasher Control Board Led Flashing

    There are several reasons why your GE dishwasher is blinking lights. Typically, a blinking light alerts you that the dishwasher needs attention.

    The blinking lights on GE dishwashers may differ from model to model, so it is best to consult your owners guide.

    You can always download another GE dishwasher owners manual if you do not want to have access to yours.

    However, two problems are common to most models.

    There Is A Problem With The Ge Dishwashers Touchpad

    How to Replace GE Dishwasher User Interface (Control Panel)

    Ge dishwasher buttons not working? When the display lights up, but the buttons do not work, the dishwasher is likely at fault. You may check for problems by seeing if some buttons respond to your touches or not.

    Try reinstalling and removing the dishwasher again to see if that fixes the issue. Also, make sure that the dishwasher door is shut.

    Your dishwashers touchpad might be defective or your control board might be defective.

    Also Check: Water Pooling At Bottom Of Dishwasher

    Ge Dishwasher Not Starting Check These 4 Things

    Your dishwasher is loaded and the detergent dispenser is filled, but nothing happens when you press the Start button. Does this sound familiar? Though a GE dishwasher not starting can feel like a cause for panic, theres no need to fear the worst. Checking for common causes like power issues and incorrect cycle settings can solve the problem quickly and easily.

    Also Check: Whirlpool Dishwasher Heat Dry Not Working

    Dishwasher Control Panel Problems

    If you are experiencing dishwasher control panel problems,chances are an easy fix will do the trick. There are several easy options thatmay be causing your dishwasher control panel problems, including the following:

    • The dishwasher control panel needs to be reset.
    • The dishwasher control panel problem is causedby a lack of power.
    • A child lock has been activated, causing yourdishwasher control panel problems.

    However, other dishwasher control panel problems may suggestthat the dishwasher control panel will need to be replaced. These include:

    • The control panel lights are blinking, or turnedoff.
    • The control panel keys are stuck.
    • Your dishwasher will not run.

    Don’t Miss: Dishwasher 18 Inch Stainless Steel

    Ge Dishwasher Control Board Led Codes

    Most modern machines, including your GE dishwasher, have different LED lights. These lights tell you the operation that the device is undergoing.

    But these lights also tell you the problem your dishwasher may have while in diagnostics mode.

    Since the signs underneath these lights do not correlate with the problem they signal, you will have to look through the diagnostics guide.

    Doing this will help to decode what each light means and what it means when it flashes more than once.

    The LED lights on your dishwasher can indicate a problem in communication, water temperature, or turbidity. Other times, the lights might flash several times at a go. You should know that the number of times the light flashes has a different meaning. It could signal a problem with the inlet valve, drain, or circulation pump.

    This article will examine how to diagnose the different LED codes, why the LED lights are flashing, and what they mean. We will also consider how to tell if your control board is bad.

    Check The Child Safety Lock

    GE WB07X10882 Assy

    Most dishwashers include a child lock feature to prevent kids from opening the appliance or changing the cycle settings. In many cases, the unit will not run while the child lock is engaged. Usually, the lock can be activated and deactivated by pressing and holding a button for three seconds, or something similar. If your dishwasher wont run and the door wont open, check the manufacturers instructions for the child safety lock.

    Recommended Reading: Granite Grabbers Dishwasher Mounting Brackets

    Check For Power To Dishwasher And Control Panel

    About this: Troubleshooting control panel problems can be time-consuming and potentially expensive. Thats why you must always start with the simplest causes to either rule out or fix. In the case of your GE Profile dishwasher, that means checking its power supply.

    The power supply is often overlooked during troubleshooting. But if its the root cause, you can fix it quickly and get your dishwasher working in moments.

    Firstly, you must ensure that theres a power supply to your dishwasher. Then, inside the appliance, you must ensure that power is being supplied to the control panel.

    Check The Wiring Harness

    The wiring or cable harness consists of various wires that connect to various parts of the dishwasher. On most models, the wiring harness can be found with the control panel. Excess heat sometimes damages the wiring harness, or wires can melt and attach to the dishwasher.

    • Examine the wiring harness for any of the above issues.
    • Replacing the wiring harness is difficult and should only be attempted by professionals. This is especially true if multiple wires need to be replaced. A mistake will likely be costly and dangerous.
    • Replacing a couple of easily accessible wires is slightly easier, but it is still best repaired by a professional.

    Don’t Miss: Water In The Bottom Of The Dishwasher

    Check The Dishwasher Power Cord

    Some dishwashers have a power cord that plugs into an electrical outlet under the sink, while other dishwasher power cords are wired directly from the wall to the wires in the dishwashers junction box. If your dishwasher power cord plugs into an electrical outlet, make sure the power cord is plugged in.

    If the power cord is plugged in, its possible the electrical outlet doesnt work. Check the electrical outlet for power by plugging in a small lamp. If it doesnt light up, have an electrician repair the bad outlet.

    Heres a helpful troubleshooting video that shows this step and additional troubleshooting steps to take when your dishwasher has now power.

    Why Should I Reset My Dishwasher

    GE Dishwasher Dead Display Diagnosis (GE Dishwasher Has No Lights)

    There are various reasons to reset the GE dishwasher. You should reset your GE dishwasher when your dishwasher stops running due to glitches or technical failure.

    Like other electronics appliances, when you reset the dishwasher, it does fix minor errors or glitches in the dishwasher.

    But, resetting wont fix the problem if there are technical issues inside the dishwasher. You should look after other solutions.

    Don’t Miss: Dishwashers On Sale At Home Depot

    Press The Start/reset Button

    If the lights are blinking and the dishwasher is beeping, it can be as simple as pressing the Start/Reset button to return the dishwasher to normal. The issue could also be caused by the door being open, where closing the door properly resolves the issue. If the issue remains, disconnecting the power will likely solve the problem.

    To Summarize You Should Be Able To Reset Your Ge Dishwasher By One Of The Following:

    When the light stops flashing, the dishwasher is reset and it can be restarted later. How to reset a ge dishwasher 7 s ge pro quiet power 2 dishwasher john torrance ge dishwasher won t drain reviews by wirecutter dishwasher won t drain what to check ge dishwasher not draining repairfixed ge triton quiet power ii won t drain gsdl352f01ccjohn torrance ge dishwasher won t drainge dishwasher not draining repairjohn read more »i dont have a. First, hold the start button so that the machine stops working or light starts blinking to indicate that the machine is on reset mode.

    Don’t Miss: How Much Is Dishwasher Installation

    RELATED ARTICLES

    Most Popular