How To Reset Ge Dishwasher Leak Detected
There are various error codes that can take place inappropriately. One of those is LEAK DETECTED or 999. Those error messages can be reset.
If you are getting an error message and the problem has been fixed, you can reset the error message by resetting the dishwasher. This is done by turning off the dishwasher power at the circuit breaker or unplugging it from the wall. Wait five minutes before reestablishing the power and the error message should be gone.
It is important to make sure that the leak is actually fixed before you reset the error code. At times, the leak detected error can show up inappropriately. That error code may also be 999 on some units with a floor protect feature.
Any error code can be reset by doing a hard reset of the dishwasher. It is not always going to be appropriate to do so, especially in the case of a water leak.
Resetting the error code can be damaging to your home because you may not recognize that the leak is still ongoing. Always ensure that you have the unit serviced when this error message shows up.
How To Start Blomberg Dishwasher
To start your Blomberg dishwasher, ensure there is no water or debris around the base of the machine. If there is, clean it up before proceeding. Next, locate the power button on the control panel. Press the power button for three seconds to turn on the dishwasher. The display will light up, and the dishwasher will begin to fill with water. Once the dishwasher is complete, press the start button to begin the cycle. Alternatively, you can select a cycle using the control panel and press the start button. The dishwasher will run through that cycle and automatically shut off when it is finished.
If you need to pause the dishwasher, press the pause button. The machine will stop, and the display will indicate that it is paused. To resume the cycle, press the start button again.
To cancel the cycle, press and hold the power button for three seconds. The dishwasher will empty and then shut off.
Problem With Water Supply
Water supply issues can also be responsible when your GE dishwasher wont start. Make sure the water supply valve to the dishwasher is in the on position and assess the water supply hose for kinks or tears. While you can carefully straighten any kinks in the hose, a cracked or leaking hose requires replacement.
If the supply valve and hose are functioning properly, a GE dishwasher not starting may be due to a defective water inlet valve. This valve opens and closes to allow water to enter the dishwasher at the right points in the wash cycle. We suggest that a professional service assess and replace the water inlet valve as needed.
Don’t Miss: Bosch Silence Plus Dishwasher Manual
Ge Dishwasher Not Starting Wash Cycle
Here are some possible causes and how to fix them.
If your GE dishwasher doesnt seem to be starting the wash cycle, there could be a few different reasons why. First, check to make sure that the dishwasher is properly plugged in and that the power source is working. If thats not the problem, then it could be an issue with the dishwashers door latch. Try opening and closing the dishwasher door to make sure that its properly latched.
If neither of those solutions seem to be working, then there could be a problem with the dishwashers control panel. If the control panel isnt working properly, you may need to replace it.
Dishwashers Controls Are Locked

One situation where the controls become unresponsive is when the child lock is engaged. With this mode enabled, any button you press will not respond.
Depending on the model, you may have a dedicated button for the lock, or it might share the Heated Dry button.
To unlock the GE dishwasher, double-tap the Lock button, then the light above it will go off. In other models, press and keep holding the Heated Dry button for 3 seconds until you hear a beep, followed by the light going off.
If you are sure that the controls have frozen due to an error, then you will have to perform a quick reset.
Recommended Reading: Maytag Dishwasher Top Rack Replacement
How To Fix A Ge Dishwasher That Wont Start
GE makes a great range of dishwashers, but that doesnt mean they dont break down from time to time. One of the most common problems people have with their GE dishwashers is when they wont start.
If this is happening with your GE dishwasher, follow the steps in this guide to find the cause of the problem and fix it. Please note that you will need to have a multimeter to carry out the majority of these steps if you dont have one or dont know how to use one, youll need to get a qualified technician to come and inspect your dishwasher.
This guide covers most GE dishwasher models, including:
DDW550B-45
WD26X10016
Old Ge Dishwasher Not Starting
Here are some possible causes and how to fix them.
One possible reason why your old GE dishwasher isnt starting could be because the door latch is not engaging properly. To fix this, make sure that the door is firmly closed and check the door latch for any damage. If the door latch appears to be damaged, you will need to replace it.
Another possible reason why your dishwasher isnt starting could be because the start switch is not working properly. To test this, you will need to access the control panel and press the start switch. If the switch does not click or feels loose, you will need to replace it.
If your dishwasher still does not start, there could be an issue with the electrical supply. First, check to make sure that the dishwasher is plugged into a working outlet. If the dishwasher is plugged in and still not working, you will need to call a qualified electrician to check the wiring.
Read Also: Samsung Dishwasher Won’t Turn On
How Do I Start My Ge Dishwasher
Controls for the Dishwasher Prior to starting the washing cycle, you may choose from a variety of preset wash plans and choices in the GE dishwasher. You then hit the Start/Reset button to begin the cycle after you have picked your options. The cycle will begin with the dishwasher filling with water, and it should begin washing within 60 seconds of the water being added.
Door Latch Or Door Latch Switch
The door latch assembly is a must-have for any dishwasher, and its not just about preventing water from leaking. This essential component also has two functions: the first being to hold the door closed during cycles, which prevents leaks secondly, this part includes switches that supply power to your dishwasher controls!
If the door cant close properly to activate the switches or if theyre defective, then youll have trouble with your dishwasher. Inspect everything from latch assembly to switches for problems and fix them.
If the door switch is defective, their dishwasher will not work even after you close it. To see if this may be the problem for your appliance, use a multimeter and test to make sure that theres continuity coming from the door button. If there isnt any, then replace it.
Also Check: Whirlpool Dishwasher Top Rack Clips
Replace The Touchpad And Control Panel
If you still havent found the cause of the problem, the next step is to test and possibly replace the touchpad and control panel. To do that:
Ge Dishwasher Not Starting Start Button Flashing
If your GE dishwasher doesnt start when you push the start button, and the start button is flashing, it could be caused by a few different things. Here are some possible causes and how to fix them.
One possible cause is that the dishwasher isnt getting power. Check to make sure that the dishwasher is plugged in and that there is power to the outlet. If the dishwasher is hardwired, check the circuit breaker.
Another possible cause is that the door isnt closed properly. Make sure that the door is shut all the way and latched.
If neither of these things seem to be the problem, then there may be something wrong with the start button itself. Try pressing and holding the start button for a few seconds. If that doesnt work, you may need to replace the start button.
Read Also: Why Wont My Dishwasher Turn On
S To Run A Ge Dishwasher
If everything is all set, here’s how to operate your GE dishwasher:
That’s it! You can now finally relax and wait until the cycle finishes. Typically, a pot scrubber takes 74 minutes, 53 minutes for Normal Wash, and only 14 minutes if you choose the Rinse & Hold cycle.
Put The Dishwasher In Service Mode To Reset The Dishwasher

Most GE dishwashers will have a service mode that can be activated to reset the dishwasher. Service mode is also where you can run diagnostic tests to identify a faulty component. The dishwashers service manual or tech sheet explains how to operate the dishwasher in service mode. The service manual can usually be found behind an access panel near the water inlet valve.
If this reset method does not apply to your model, finding its service manual will give you precise instructions for how to enter service mode and reset your specific GE dishwasher.
To put the dishwasher in service mode, hold the Select Cycle button and the Start button down for five seconds. Next, to reset the dishwasher, press the Select Cycle button for five seconds. This should activate the lock button light. Press Select Cycle again for five seconds. Hold the Start button now for five seconds. The Start button should start flashing. Finally, hold the Start and Select Cycle button down for five seconds. The dishwasher control panel should now light up, and the dishwasher should be ready to go.
GE allows you to search your specific model number to access the manual for your dishwasher. If the above instructions have failed to solve your issue, locate its manual on the GE website here.
Recommended Reading: Ge Dishwasher Wont Turn On
Test The Door Latch Switch
Remove the inner door panel to access the door latch assembly at the top of the door. Make sure the catch engages the door latch switch when it is inserted into the latch assembly. If all appears to work properly, use a multimeter to test the switches for continuity. With the multimeter set on Rx1, touch the probes to the switch terminals. The reading should be at or near zero. If your reading is different, replace the door latch assembly.
What Do Flashing Display Lights And Sounds Mean In Ge Dishwasher
Status Indicator Lights and Sounds | What does it mean? |
START/RESET | The cycle has been interrupted by pressing the START/RESET pad. Light will quit flashing after the dishwasher automatically drains out the water. |
Sanitized | Displayed at end of the cycle when Wash Temp Sani or Sanitize Temp has been selected and the dishwasher has met requirements for sanitization. |
Clean | Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean. The light will turn off when the door is opened. |
Cycle Status | The indicator light on the door front will change color to indicate the wash status. During the wash cycle, the indicator light will be amber. When the wash cycle is complete, the light will change to white. |
Sounds | The dishwasher will emit a sound to indicate cycle completion, button presses, and door ajar. |
Mute | To turn the dishwasher control sounds ON/OFF, press the Dry Boost pad 7 times within 5 seconds. |
Don’t Miss: Built In 18 Inch Dishwasher
What Happens If You Dont Put Salt In A Dishwasher
If you dont put salt in your dishwasher, your dishes may not come out as clean as they would if you did use salt. This is because the salt helps to break down the food and grease on your dishes, making it easier for the dishwasher to wash them clean. Additionally, without salt, your dishwasher may not be able to reach its optimal washing temperature, which can also impact the cleanliness of your dishes.
Check The Child Safety Lock
Most dishwashers include a child lock feature to prevent kids from opening the appliance or changing the cycle settings. In many cases, the unit will not run while the child lock is engaged. Usually, the lock can be activated and deactivated by pressing and holding a button for three seconds, or something similar. If your dishwasher wont run and the door wont open, check the manufacturers instructions for the child safety lock.
Don’t Miss: Best Dishwasher Detergent For Cloudy Glasses
Ge Dishwasher Door Light Flashing
The door light of the dishwasher is also the same one assigned to the Start button. So whenever you see this door light flashing, most often, its used to indicate that the door is not fully closed.
Try closing the door all the way in, and if the blinking doesnt go away, then you have an issue with the doors latch, whether its a broken latch or the sensor is not working correctly.
Another situation where this light would be blinking is during a quick reset. After you press the Start/Reset button, this light will be flashing for a couple of minutes until the dishwasher completes the reset process.
How Do You Reset A Ge Profile Dishwasher
2020-03-25 ·Press the Start/Reset button on the dishwashers control pad to reset the GE Profile dishwasher after a cycle has already started. This will cancel the current cycle. The water will start to pump out of the dishwasher for a few moments. Meanwhile, the Start/Reset light will flash on
- Part Numbers: WB15X24435, AP5957851, WB15X10216, PS10065137
- Ultra Durable, Replacement Microwave Oven Door Handle for General Electric Microwave
- Premium Quality: We utilize premium, highly durable materials guaranteed to exceed OEM specifications
- Fit Models: JVM1540SM1SS, JVM1540DM1BB, HVM1540LM1CS, HVM1540DM1BB, JVM1540LM1CS, JNM1541DM1BB, HVM1540DM2BB, HVM1540LM2CS, JNM1541DM2BB, JNM1541DM2CC, JNM1541DM2WW, JNM1541DM3BB, JNM1541DM3CC, JNM1541DM3WW, JNM1541DM4BB, JNM1541DM4CC, JNM1541DM4WW, JNM1541DM5BB, JNM1541DM5CC, JNM1541DM5WW, JNM1541DM6BB, JNM1541DM6CC, JNM1541DM6WW, JVM1540DM2BB, JVM1540DM3BB, JVM1540DM3CC, JVM1540DM3WW, JVM1540DM4BB, JVM1540DM4CC, JVM1540DM4WW, JVM1540DM5BB, JVM1540DM5CC, JVM1540DM5WW, JVM1540DM6BB
- JVM1540DM6CC, JVM1540DM6WW, JVM1540LM2CS, JVM1540LM3CS, JVM1540LM4CS, JVM1540LM5CS, JVM1540LM6CS, JVM1540SM4SS, JVM1540SM5SS, JVM1540SM6SS, JVM1810DS1BB, JVM1810DS1WW, JVM1810SS1SS, JVM2010DS1BB, JVM2010DS1WW, JVM2010SS1SS,
Also Check: Ge Dishwasher No Lights On Control Panel
Ge Dishwasher Not Filling With Water
Your GE dishwasher may not be filling with water because of a clog in the fill hose, a leaking faucet, or damaged water line.
- Turn off the power and remove the access panel.
- Unscrew the screws that secure the fill tubing to the dishwasher and take it out.
- Inspect the fill tube to ensure there are no obstacles or debris that might impede the waters flow.
If there are any obstacles, use wire-nosed pliers to remove them. You can get the INGCO Pliers Tool if you dont already have a pair with you.
Also, I recommend that you inspect both the water supply line and the faucet for leaks and replace them if need be.
Turn the water back on and test your dishwasher to see whether it has filled with water if everything appears to be in order.
Ge Profile Dishwasher Shows Code 1h Will Not Start

2018-05-03 ·GE dishwasher control panels All work the same to reset 1h code . Press the START button to cancel DELAY START GE Dishwasher . This usually happens when you have inadvertently bumped or pressed the DELAY HOURS button. To reset this back to normal, HOLD AND PRESS THE START BUTTON. MORE INFORMATION = Water In Bottom Of Dishwasher How To Fix
- This is an O.E.M. Authorized part
- This is an authorized aftermarket product
- Fits with various WD21X10519 brand models
Don’t Miss: Dishwasher Detergent For Hard Water
How To Fix Ge Dishwasher Start Button Not Working
Are you having trouble getting your GE dishwasher to start? Are you working on your second load and wondering why the dishwasher wont run again?
There are few things worse than the feeling of being stuck in the kitchen when the dishwashers not working! Luckily, these troubleshooting tips can help you get back to washing dishes so you can start enjoying life again!
I was also able to solve the problem when I went through these steps but I was deeply worried when this problem occurred.
I spent a ton of money on this product and when it stopped working, it was a period of disguise for me.