Wednesday, September 27, 2023
HomeGEHow To Install Ge Dishwasher

How To Install Ge Dishwasher

Install The Electrical Circuit

How To Install A GE Dishwasher – Installation

The first step is to install a 20-amp circuit from the electrical service panel if one is not already installed. To add a circuit cable, drill a hole down through the floor into the basement or crawlspace.

Install 12 AWG cable from the dishwasher space to the service panel. Leave about six feet of cable sticking through the hole by the dishwasher. This will allow the dishwasher to be pulled out during servicing. Tape the wire to the floor with a piece of duct tape so it doesn’t slip down through the hole.

Have an electrician install a new circuit breaker in the service panel and make the final wiring connections. If there is an existing circuit for the dishwasher, be sure that the power is turned off to the circuit.

The Spruce / Kevin Norris

How To Install A Ge Dishwasher

Avoid the hassle of hand-washing dishes by installing a GE dishwasher in your home’s kitchen. Most of today’s homes are built the with the wiring and plumbing for a built-in dishwasher already installed. Consult a plumber and an electrician or a general contractor if your home does not have these items. Working with the electrical wiring is too dangerous a project for most homeowners to attempt without professional assistance.

  • Switch off power to the kitchen cabinet area from the home’s circuit breaker panel. A built-in GE dishwasher must be directly connected to the home’s electrical wiring instead of plugging into a wall outlet, so it is vital that you know the power is off before you proceed with the installation. Close the water shut-off valve under the sink.

  • Lay a piece of scrap plywood or a thick blanket in front of the cabinet opening to protect your kitchen floor. Have an assistant help you unpack the dishwasher and lift it onto the wood or blanket. Attach the drain hose and water supply line to the back of the dishwasher.

  • Connect the electrical wires from the home to the power supply of the dishwasher. Match the black wires on each side with each other. Do the same with the white wires. Ground the circuit by wrapping the green wire from the house around the ground screw on the dishwasher.

  • Run a test cycle with no dishes in the racks to make sure all of the connections are secure and no water is leaking out of the dishwasher.

  • References

    How Do I Hire An Appliance Installer

    To find an appliance installer near you, start searching on Thumbtack. This way, you see a list of nearby pros offering services and compare based on their customer review, ratings and profile pages. You can also find customer-uploaded photos showing pictures of the pros work.

    Check for licensing requirements in your state, and make sure whoever you work with abides by them. Finally, contact several different pros to compare their rates.

    You May Like: Kitchen Aid Dishwasher Parts List

    Affiliate Programs Keeps Allthumbsdiy Free

    AllThumbsDIY.com participates in the , an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.

    Additionally, AllThumbsDIY.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.

    *Amazon and the Amazon logo are trademarks of Amazon.com, Inc., or its affiliates

    Attach Water Supply Line

    How To Install A Dishwasher

    The dishwasher connector kit also includes a braided steel water supply tube. Thread the coupling nut of the supply tube onto the dishwasher 90 fitting, and tighten with channel-lock pliers or an adjustable wrench. This is a compression fitting that does not require pipe joint compound. Be careful not to overtighten, as it is possible to strip the threads.

    The Spruce / Kevin Norris

    Read Also: What Is The Best Dishwasher On The Market

    Page : Dishwasher Installation

  • Page 8 Figure J attached to the dishwasher frame and toward the center of the dishwasher as shown in Figures L and M. Place the hose clamp over the small end of the Note: Check That Harness Leads Are …
  • Page 9 10 foot long hose may be purchased from an CORD, IF USED, THROUGH CABINET authorized GE appliance dealer. The 10 foot long Upright the dishwasher and position it in front of hose is part number GPF10S. the cabinet opening.
  • Page 10 If the insulation is bunched up or interfering with the springs, Adjust the level of the dishwasher by individually straighten and re-center the blanket prior to sliding turning the four legs on the bottom of the 06F-1847Da the dishwasher into its final position.
  • Page 11 Make sure the door spring does not rub against the or control panel damage. ll hose or water supply line. Make sure the dishwasher is centered in the cabinet and the door opens and closes freely without hitting the adjacent cabinets. Drive mounting screws…
  • Page 12 IMPORTANT Total drain hose length must plug has been removed. Dishwasher will not drain not exceed 10 feet for proper drain operation. if plug is left in place.
  • Page 13 Steps 13 and 14 Pull lower rack about halfway out. Check to be sure it does not roll back into dishwasher or further out. If it does, re-level the dishwasher. See Step 12 Check to be sure control panel does not touch …
  • This manual is also suitable for:

    Turn Off The Water And Electricity In Your Kitchen

    Before you touch your dishwasher, start by cutting off the electricity and water supply to the kitchen. Youll be removing and adding a new appliance that needs both to work, so you dont want to risk a water leak or shock during the process.

    Youll want to find your homes breaker box and turn off the electricity to the kitchen. To turn off your water supply line, find the shutoff valve and ensure it is off. Unplug your dishwasher and disconnect the dishwasher drain hose currently connected under your sink.

    Note: Theres probably a good amount of dirty water and food gunk that will spill from the drain hose once you unplug it. Have a bucket ready to catch any excess water draining from the pipe.

    Don’t Miss: Ge Dishwasher Heated Dry Not Working

    What Do Flashing Display Lights And Sounds Mean In Ge Dishwasher

    Status Indicator Lights and Sounds What does it mean?
    START/RESET The cycle has been interrupted by pressing the START/RESET pad. Light will quit flashing after the dishwasher automatically drains out the water.
    Sanitized Displayed at end of the cycle when Wash Temp Sani or Sanitize Temp has been selected and the dishwasher has met requirements for sanitization.
    Clean Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean. The light will turn off when the door is opened.
    Cycle Status The indicator light on the door front will change color to indicate the wash status. During the wash cycle, the indicator light will be amber. When the wash cycle is complete, the light will change to white.
    Sounds The dishwasher will emit a sound to indicate cycle completion, button presses, and door ajar.
    Mute To turn the dishwasher control sounds ON/OFF, press the Dry Boost pad 7 times within 5 seconds.

    What To Consider Before Installing Your Dishwasher

    How to Install a GE Appliances Plastic Tall Tub Dishwasher

    The Bosch 800 Series SHPM88Z75N is the best dishwasher you can buy.

    Before you get your new dishwasher, youll want to make sure your kitchen is fully prepped to have the new dishwasher delivered . Start by measuring everything to make sure you have the clearance in your home to have a new appliance delivered, measuring the space where your dishwasher will go to ensure a snug fit, and clearing out enough space in your home to house the new dishwasher while you prepare to install it.

    Next, youll want to get all the tools you need to complete the job. Your dishwasher delivery will include smaller tools like screws, brackets, and clamps, but youll want to have some standard home improvement tools on hand, like a screwdriver, pliers, wrench, measuring tape, power drill, and flashlight.

    Finally, you may want to consider calling in a buddy to help you through the process, either physically or emotionally. I was lucky to have a live-in spouse who did all the things I didnt want to . A delivery team will be able to move the appliances, but a buddy can help trade-off if youre struggling with a screw, or provide much-needed positive reinforcement throughout the journey.

    Recommended Reading: Bosch Dishwasher E 24 Code

    How Much Does It Cost To Install Appliances

    Installing a new appliance costs $125, on average. However, homeowners should expect to pay within the range of $120 to $150.

    For less complex appliance installations, you may pay a low-end cost ranging between $65 and $100. On the other hand, more complex appliances like laundry machines, ranges and other items can cost between $175 and $326 to install. Ask whichever appliance installation service you hire to give you a price quote, if possible.

    Should You Tip Appliance Installers

    You can tip appliance installers if you feel their service has gone above and beyond. A standard tip is between $10 and $20.

    Reasons you might consider tipping include a very pleasant customer service demeanor, having to carry a heavy appliance up or down the stairs, working in inclement weather, taking care not to make a mess and other acts of care and consideration. You are not obligated to leave a tip but one is always appreciated.

    Recommended Reading: Maytag 577-1 Dishwasher Manual

    Remove Your Existing Dishwasher

    Start by finding and removing your dishwashers toekick. The toekick is a metal plate at the base of your dishwasherit should be easily removed with a screwdriver, and will allow you to see underneath your dishwasher.

    Once the toekick is out, youll want to unscrew the leveling legs found in each of the four corners of the dishwasher base. You can do this with your arms or an extended wrench, just make sure you start with the legs in the back. By unscrewing the leveling legs, you will create space between your dishwasher and the counter, allowing you to slide the dishwasher out once youve created enough.

    If you cannot comfortably reach under your dishwasher or get the leveling legs to budge, call a handyman to help.

    Are There Ways To Be Safe If I Hire An Appliance Repairman Or Specialist When Social Distancing

    How to Install a GE Profile PDW9200 Dishwasher

    If you decide to hire an appliance service specialist or repairman, check your local news for community guidelines and follow the CDCs guidelines for social distancing. Discuss safety protocols with the appliance repairmen before they enter your home. And when they enter your home, stay at least 6 feet apart, dont shake hands, sanitize all involved surfaces and use digital payments instead of cash or a check.

    If you decide to postpone the work, consider buying a gift card from them or paying for future work. This is a great way to give back to the community, as many small businesses and individual contractors are feeling the economic effects of social distancing.

    Read Also: Best Eco Friendly Dishwasher Detergent

    Check The Water Temperature

    The entering water should be at least 120°F and not more than 150°F for effective cleaning and to prevent dish damage.

    1. Check the water temperature with a candy or meat thermometer.

    2. Turn on the hot water faucet nearest the dishwasher.

    3. place the thermometer in a glass and let the water run continuously into the glass until the temperature stops rising.

    Ge Cafe Dishwasher Sticks Out Too Far

    We are currently having a home built and our dishwasher appears to have been installed incorrectly. It is a GE Cafe dishwasher that is mean to be flush mounted with the cabinets. However, in its current state the entire door protrudes out.

    The installation manual states: This dishwasher is capable of a true-flush installation at a 24 deep opening. The pictures from the GE Cafe website show it flush-mounted with the dishwasher pushed back far enough under the counter that when closed the top of the dishwasher door would be concealed.

    Flushed with Cabinets

    Dishwasher unit set back far enough to accommodate door under counter

    Our countertop is made of Quartz. Therefore, the dishwasher was secured to the face frames of each adjacent cabinet instead of the countertop. This created the issue we have now with the door protruding out and not under the counter overhang. The installation manual specifically states: Do not screw into the cabinet face frame.

    So my questions are: What should the dishwasher be secured to? The installation manual says secure it to the cabinet sides. Has anyone ever done this?

    Read Also: Double Sink Plumbing With Garbage Disposal And Dishwasher

    Connecting The Electrical Supply

    Always be sure to cut off the power to the dishwasher by flipping the circuit breaker before attempting to connect the electrical supply. Run the cable through the back of the electrical box on the dishwasher, and connect the hot and neutral wires to the corresponding wires in the box using wire nuts. Be sure to connect the ground wire to the green screw and replace the cover on the box.

    Turn the water back on and check for leaks, then turn on the power and run the dishwasher through a full cycle. If everything works properly, slide the machine into the cabinet, being careful not to crimp or pinch the pipes. Plumb and level it by raising and lowering the adjustable feet on either side.

    Screw the dishwasher to the underside of the countertop to hold it in place. When attaching the mounting screws to the plywood used to support a stone countertop, be sure the screws do not protrude into the stone.

    Attach the faceplate to the base, and your new dishwasher is ready to go!

    Connect Water Drain And Electric Lines

    Installing a New GE Profile Dishwasher: How to Install a Dishwasher (DIY)

    Tip the dishwasher upright and slide it into its space. Then, get on the floor to connect lines to the dishwasher.

    • Connect the water supply line to the 90-degree fitting, using pliers to ensure a tight fit.
    • Turn on the water supply, inspect for leaks and tighten connections if necessary.
    • Connect the drain hose according to manufacturers instructions.
    • Complete the electrical connections using wire nuts and following the installation guide.

    With the water supply, drain and power lines are attached, turn on the electricity at the circuit breaker and check the dishwashers operation before securing it into place.

    • Make sure that the front of the unit is flush with the cabinet fronts.
    • Use a level to ensure that the appliance is level and plumb so that it drains properly.
    • Adjust the leveling legs as necessary and tighten the locknuts.
    • Confirm the dishwashers placement and make any necessary adjustments.
    • Use the included brackets to secure the unit to the underside of the countertop and the adjacent cabinets.
    • Replace the front access panel.

    Homeowners with a moderate amount of experience working with plumbing and electricity can learn how to install a dishwasher. If you need any necessary tools, dishwasher parts or other supplies, remember that The Home Depot delivers. Just say when, where and how. If installing a dishwasher is a bigger project than you care to do yourself, consider adding appliance delivery and installation service to your purchase.

    Shop this Project

    You May Like: How To Deep Clean Your Dishwasher

    How To Replace A Ge Dishwasher Drain Pump

    Do you need to replace the drain pump in your GE dishwasher? Then this guide is for you. The drain pump removes the wastewater after each cycle, so when it stops working, you are unable to use your dishwasher. Thankfully, it is quite a straightforward repair to carry out.

    In this guide, you will find step-by-step instructions for how to remove the old drain pump and then reinstall the new pump. When replacing a part, always make sure you check that it is the manufacturers recommended part that you are using.

    This guide covers most GE dishwasher models, including:

    DDW550B-45

    What Customers Are Saying:

    Thank you for the expeditious answer. It’s good to know you’re out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air.

    JeanRiverhead, NY

    You did one super job of explaining to me everything there is to know about this fridge. I’m looking forward to asking you questions in the future.

    JimmyBagley, IA

    Wonderful service, prompt, efficient, and accurate. Couldn’t have asked for more. I cannot thank you enough for your help.

    Mary C.Freshfield, Liverpool, UK

    This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

    AlexLos Angeles, CA

    Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

    GPHesperia, CA

    I couldn’t be more satisfied! This is the site I will always come to when I need a second opinion.

    JustinKernersville, NC

    Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

    EstherWoodstock, NY

    Read Also: 18 Inch Stainless Steel Dishwasher

    Connect The Water Line

    To install the water line to the dishwasher, you’ll need to connect to a shutoff valve on the hot water supply pipe under the sink. The easiest way to do this is to replace the existing shutoff valve with a dual-outlet shutoff valve so the same valve can serve the sink faucet and dishwasher.

    Feed 3/8-inch flexible copper supply tubing through the cabinet hole and connect one end to the shutoff valve. Connect the other end to the dishwasher’s water valve, following the manufacturer’s directions. You’ll likely need to add a brass fitting to the water valve to accommodate the 3/8-inch water line. Use thread seal tape on all connections to help prevent leaks.

    The Spruce / Kevin Norris

    RELATED ARTICLES

    Most Popular