Make Sure The Door Switch Is Working
The second step is to make sure the door switch is working correctly. The purpose of the door switch is to prevent the door from opening during a wash cycle. Sometimes they can become faulty, and this causes the control panel to believe the door isnt shut properly, which results in the control panel not letting the dishwasher start.
Checking the door switch requires testing it with a multimeter to do that:
Ge Dishwasher Beeps 3 Times And Wont Start Find Solutions Here
What you find on this page:
Having a dishwasher stops us from having to do the dishes manually, making the task quicker, easier, and safer. But what do three beeps on a GE dishwasher mean? And what do you do when your GE dishwasher beeps three times and wont start? When this occurs, several issues are sometimes responsible.
If youve been dealing with this issue, were here to help. If your GE dishwasher beeps three times and wont start, read on to find solutions and troubleshooting tips.
Ge Dishwasher Not Starting Light Blinking
Here are some possible causes and solutions to fix the problem.
One potential reason your GE dishwashers not starting light is blinking could be due to a power issue. Make sure the dishwasher is plugged into a working outlet, and if it is, try resetting the circuit breaker.
Another possibility is that the door isnt closed properly. check to make sure the door is shut all the way and that theres nothing blocking it from latching.
If neither of those solutions fixes the problem, then its likely an issue with the dishwasher itself. You can try resetting it by unplugging it for 30 seconds and then plugging it back in. If that doesnt work, you may need to call a repairman.
You May Like: Stainless Steel Built In Dishwasher
Whirlpool And Kenmore Control Lock
To turn the control lock ON, press the Heated Dry pad for 4-6 seconds. Look for the lock icon to glow. Pressing any part of the pad while its on will make the light flash three times.
But the dishwasher will not respond to the selection. To turn the control lock OFF, press the Heated Dry pad for 4-6 seconds. Look for the lock icon to stop glowing and try to start the machine.
Test The Door Latch Switch
Remove the inner door panel to access the door latch assembly at the top of the door. Make sure the catch engages the door latch switch when it is inserted into the latch assembly. If all appears to work properly, use a multimeter to test the switches for continuity. With the multimeter set on Rx1, touch the probes to the switch terminals. The reading should be at or near zero. If your reading is different, replace the door latch assembly.
Don’t Miss: Home Depot Dishwashers On Sale
Ge Dishwasher Not Starting Check These 4 Things
Your dishwasher is loaded and the detergent dispenser is filled, but nothing happens when you press the Start button. Does this sound familiar? Though a GE dishwasher not starting can feel like a cause for panic, theres no need to fear the worst. Checking for common causes like power issues and incorrect cycle settings can solve the problem quickly and easily.
Check The Door Switch Operation
The door switch is commonly a culprit when a dishwasher wonât start or run.
Here you may need to enter the error code mode .
To switch to the diagnostics error code mode:
When the appliance is in Stand-by Mode , proceed to press and hold down these two buttons combined for 5 seconds..
Cycle Select + Start .
The machine will perform a Door Status Check for 10 seconds on entering diagnostic error codes mode.
Note that if all the LEDs illuminate solidly, the door will have been detected as latched firmly.
On the other hand, you should try to shut the door correctly if all the LEDs are flashing at the end of the check.
Quick Tip: Be sure to press the âStartâ pad within 5 to 10 seconds of shutting the door.
Side note: These machines also usually fail to start if the door latch is not functioning properly so it is important to check and repair/replace the latch, if needed.
Remember to troubleshoot door problems further if they persist .
Read Also: Are Souper Cubes Dishwasher Safe
Ge Dishwashers Lock Light Is Blinking
Depending on the model, some controls start blinking their Lock light when the child lock is enabled. When this happens, the controls on the dishwasher are unresponsive, and several buttons will also start blinking when you press on them.
So before you start to panic and do a hard reboot. We suggest that you check if the child lock is enabled.
In some models, the light above the Lock button will be blinking or just switched on. If there is no Lock button on your control panel, then look for the Heated Dry button, which also shares the Lock function.
You can disengage the lock by pressing the Lock button twice or holding the Heated Dry button for 3 seconds.
Put The Dishwasher In Service Mode To Reset The Dishwasher
Many GE dishwasher models have a service mode that you can utilize. Some also refer to this mode as diagnostic mode. Regardless of the term, the function is the same.
You can enter this function on most models by holding the Start button down for five seconds. Then, once the Start button begins flashing, hold the button down along with the Select Cycle button for another five seconds.
In some other models, you can enter it by holding down only the Cycle Select button. But, again, consult your instruction manual to see the proper method for your device.
Also Check: Parts Diagram For Kitchenaid Dishwasher
Check These Elements And Parts If Ge Dishwasher No Power
If it turns out that these nine reasons are also not what happened to your unit, hold on a little longer because we will try to give suggestions to examine some of the elements and interiors of this unit.
Before we begin, we hope you first turn off all electricity to the unit. The goal is that when inspecting elements and parts, there is no additional risk. If so, proceed with checking in some parts of this dishwasher:
What Customers Are Saying:
Thank you for the expeditious answer. It’s good to know you’re out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air.
You did one super job of explaining to me everything there is to know about this fridge. I’m looking forward to asking you questions in the future.
Wonderful service, prompt, efficient, and accurate. Couldn’t have asked for more. I cannot thank you enough for your help.
Mary C.Freshfield, Liverpool, UK
This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!
AlexLos Angeles, CA
Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.
I couldn’t be more satisfied! This is the site I will always come to when I need a second opinion.
Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.
Don’t Miss: What Is The Quietest Dishwasher Decibel
Turn Off The Power Before Disassembling The Dishwasher
Sometimes internal components malfunction and need to be replaced. If you are an experienced DIYer, you may be able to repair the broken dishwasher yourself, but before opening the machine to work on it, be sure to disconnect it from the power source. Use a multimeter to test internal components. Obtain a wiring diagram for your dishwasher model to ensure that you are testing the correct terminals.
You May Also Be Interested In Dishwashers Available On Home Depot
Does A Ge Dishwasher Have A Fuse
A dishwasher thermal fuse allows the control board to receive power. When a thermal fuse blows, the dishwasher wont start at all. If you suspect that your thermal fuse is blown, you can unplug it to test its continuity. To access the thermal fuse on your dishwasher, you will need to remove the front panel of the dishwasher and pull out the control panel.
The thermal fuse for GE dishwashers are typically located at the top of the circuit board . Next, take a multimeter and place the needle on the fuses contact. If you receive a reading of zero, then the fuse is fine. If not, then the fuse is the issue and will need to be replaced.
You May Like: Kitchen Aid Dishwasher Parts List
Connect With An Appliance Repair Tech
No in-home service calls. No appointments.
This test will use LED lights to indicate the tests being run. The lights are as follows:
- One blink means the drain pump is running.
- Two blinks indicate the water valve is filling the tub.
- Three blinks mean the circulation pump is changing the diverter.
- Four blinks indicated the heater is on.
- Five blinks show the detergent solenoid is on maximum use.
The entire test should only take six minutes at most.
Read:Should You Use Dishwasher Detergent Substitutes?
Assess The Timer Motor
The first thing you should check is the timer motor it is what regulates the dishwashers cycles from start to finish. If the timer motor isnt working properly, or at all, the dishwasher will continuously run.
After ensuring you unplugged your dishwasher or flipped off the circuit breaker switch, remove the control panel face by removing the screws on it and the latch. Open the door and remove the door panel screws and locate the timer motor.
You will see two wires at the top of the motor, remove both of them, label them with tape to tell them apart, and use an ohmmeter to assess the motor function. The setting should be on X1000 and should have a reading between 2,000 and 3,000 ohms. If the number is outside of this range, it needs to be replaced.
Also Check: How Much Does Dishwasher Installation Cost
Incorrect Dishwasher Cycle Settings
When starting your dishwasher first make sure a cycle is selected. The dishwasher will not start until a cycle is specified. Meanwhile, certain features like the GE dishwasher child lock setting or Delay Start feature can prevent an immediate start. Check your control panel display codes to see if these settings are enabled. Holding down the Start button for 3 seconds should disable any selected cycle.
In some cases, moisture or damage to the control panel could result in the GE dishwasher display not working properly, preventing cycle selection. We recommend that a professional service assess and replace the display if necessary.
Replace The Touchpad And Control Panel
If you still havent found the cause of the problem, the next step is to test and possibly replace the touchpad and control panel. To do that:
You May Like: Bosch Silence Plus Dishwasher Manual
Check The Selector Switch
This part of the dishwasher is responsible for letting you select between different options when it comes to drying, washing, etc. If your dishwasher is refusing to start, the problem could be due to the selector switch not working at all, or it might be stuck, or multiple buttons are being pressed at once. If the issue is that there is no power, you can test this with a multimeter.
If you find that the selector switch isnt working at all, find the official OEM replacement selector switch and replace the broken one with the new one.
Get Help When Your Dishwasher Wont Start
Unless its a simple issue like child lock or delay start settings, when a dishwasher wont start, you need an appliance repair company to inspect it.
It could be a simple fix that takes just a few minutes, or it could be a complex problem that requires expertise and potentially dangerous electrical components.
Dishwashers are important appliances in modern homes. A dishwasher that wont start needs to be inspected and repaired.
Theyre expensive to replace, so its always more affordable to have one repaired. If you dont have a go-to appliance repair company, use our form above to find one in your area and get a free quote.
You Might Also Like:
Don’t Miss: Are Yeti Lids Dishwasher Safe
What Are The Error Codes In A Ge Dishwasher
There are more than a dozen error codes for your GE dishwasher, which can vary depending on the model. Your appliances manual should list error codes and what they mean.
Many of them are also self-explanatory. For example, Cup Open means that the detergent cup is open and hasnt closed. Leak Detected means there is a water leak somewhere, and your appliance wont start for safety reasons.
You likely wont receive the error codes if you arent getting power to your appliance. Instead, consider contacting a professional service to diagnose the problems with your dishwasher.
Dishwasher Door Isnt Latched Shut
Lastly, the dishwasher will only start if the door is properly secured. Make sure nothing is blocking the door. Knowing how to load dishes correctly can ensure that the door closes properly. Confirm that the door is closed all the way and the latch is engaged.
If you find your GE dishwasher not starting even if the door is closed correctly, the door latch or switch may have malfunctioned. If the door latch is broken, the door switch wont signal the dishwasher to start. The door switch can also be faulty, failing to send the electronic signal that starts the dishwasher even if the latch is engaged. In either case, both components require professional replacement.Whether you need a professional dishwasher repair or some dishwasher cleaning tips, Ortegas Appliance can help. Call us with any questions or concerns.
Don’t Miss: What Is Rinse Aid For Dishwasher
Inspect The Selector Switches
Selector switches allow the dishwasher to operate on various wash, rinse, and drying settings. Each setting has its own switch, and when the control panel malfunctions, these switches will not work properly. Also, if the switches have become damaged or somehow lose their connection to the panel, the dishwasher will not power on. If this is the case, the dishwasher will need to be disassembled to replace these switches. They can typically be purchased for around $30 or more.
Fix Your Broken Dishwasher In No Time
Did you rigorously follow the instructions above, but still cant diagnose your faulty dishwasher? Or, perhaps you have already successfully replaced the problematic parts, but your appliance still wont start properly?
If you answered yes to any of these questions, it may be time to let experts handle the job. Here at Prime Appliance Repair, our team of highly skilled appliance repair specialists will have your broken appliance functioning in no time. to book your appliance repair!
Recommended Reading: Whirlpool Dishwasher Gold Series Manual
Ge Dishwashers Wifi Light Is Blinking
Most modern GE dishwashers utilize Wi-Fi to interface with your smartphone or upgrade its software. Sometimes, the Wi-Fi light in the panel will start to blink when its having connectivity problems.
To resolve this, you can try reconnecting the dishwasher to the Wi-Fi network using the following steps, but make sure to forget the dishwasher device on your smartphone :
Editor’s Pick: Best Home Warranty For Dishwashers
- Both the Basic Plan and Total Plan offer coverage for dishwashers.
- All dishwasher parts and components are included with a short list of exceptions.
- Enjoy coverage for many other home appliances and systems, including heating systems, electric systems, water heaters, and stoves/ovens.
- Get your first month free when you sign up for a single payment annual home warranty plan.
Read Also: My Frigidaire Dishwasher Won’t Start
Replace The Drive Motor
If the drive motor fails, your dishwasher will not start. Ask yourself if youve been hearing any weird noises coming from previous cycles, such as humming. This indicates that the drive motor is failing and it needs to be replaced with a new one.
Update: If you are unable to figure out why your dishwasher wont start be sure to check out our ge dishwasher not starting article for more troubleshooting tips. And if you have a different brand of dishwasher, checkout our dishwasher not starting article.