An Issue With The Ge Dishwashers Touchpad
The dishwasher is most likely at fault when the display lights turn on, but the buttons do not work. You can try checking for defects by seeing if some buttons respond to your touches or not.
Try plugging and unplugging back in and see if that solves the problem. Also, confirm that the door to the dishwasher is closed.
Your dishwashers touchpad might not be responding because of a faulty touchpad itself or a faulty control board.
Check The Door Switch Operation
The door switch is commonly a culprit when a dishwasher wonât start or run.
Here you may need to enter the error code mode .
To switch to the diagnostics error code mode:
When the appliance is in Stand-by Mode , proceed to press and hold down these two buttons combined for 5 seconds..
Cycle Select + Start .
The machine will perform a Door Status Check for 10 seconds on entering diagnostic error codes mode.
Note that if all the LEDs illuminate solidly, the door will have been detected as latched firmly.
On the other hand, you should try to shut the door correctly if all the LEDs are flashing at the end of the check.
Quick Tip: Be sure to press the âStartâ pad within 5 to 10 seconds of shutting the door.
Side note: These machines also usually fail to start if the door latch is not functioning properly so it is important to check and repair/replace the latch, if needed.
Remember to troubleshoot door problems further if they persist .
Dishwasher Wont Start Troubleshoot In 9 Steps
If your dishwasher wont start, save time and money by troubleshooting it before calling a professional. Repairing a dishwasher isnt as difficult as it might seem and can be done even if you arent particularly handy. Use this guide to help you troubleshoot major parts of a dishwasher and determine when professional help is necessary.
Recommended Reading: Parts Diagram For Kitchenaid Dishwasher
Clean The Trap And Filter System
You should also make sure that you clean the trap and filter system. This can lead to issues with dishwasher buttons as well. If the buttons are flashing, this is a sign that the trap is totally full.
The first thing you need to do is remove the bottom rack of the dishwasher. Usually, theres a cap you need to turn counter-clockwise to lift the assembly out of the dishwasher. Then, dislodge the debris that is present before putting the system back in the dishwasher. This may be enough to get the buttons working again.
Ge Dishwasher No Lights On The Control Panel

If your GE dishwasher is not lighting up the control panel, you can check a few things to see if its an issue with the wiring or the control panel itself.
1. Ensure all the power goes to the dishwasher and control panel. It can be tested by turning on all the lights in your home and checking to see if the dishwasher lights up. If it doesnt, you may need to check the fuse box for the dishwasher.
2. Try resetting the dishwasher by unplugging it and plugging it back. It will clear any error codes stored on the control panel.
3. Try replacing the control panel. If this doesnt work, it may be an issue with the wiring or board in the control panel.
Also Check: Replacement Racks For Maytag Dishwasher
Solved: Ge Dishwasher No Power No Lights
GE dishwashers are valuable kitchen appliances, but every kitchen appliance needs a check-up now and then. A silent and unresponsive dishwasher can feel like a hopeless situation. But there are several quick and easy fixes to the common problems encountered when using this machine.
Some of these solutions only require the click of a few buttons to work! Others may take more time and money to remedy, but they remain straightforward. In a couple of days at most, you will be back to admiring the shine of your dishes.
There Is A Lot Of Dirt Built Up
One of the most common reasons why dishwasher buttons get stuck is related to the buildup of dirt, grease, and oil. Particularly if you have a dishwasher with a top control panel, it is not unusual for these buttons to get stuck. Food, oil, and debris can cause one or more of your dishwasher buttons to malfunction.
If you feel like the button is stuck in place, you may want to use an ammonia based cleaner to free the stuck button. Remember to use appropriate protection if you are using this type of cleaner. You do not want to get burned, and you need to protect your respiratory system.
Recommended Reading: Bosch 800 Dishwasher Crystal Dry
How To Replace Control Board On Ge Dishwasher
Quick Tip:This YouTube video demonstrates the replacement procedure step by step .
S To Replace The Ge Dishwasher Control Panel
You May Like: Parts List For Whirlpool Dishwasher
What Are The Reasons Why There Be No Lights On The Dishwasher Control Panel
The first thing to consider is whether the dishwasher has power. Its easy enough to test by plugging in another appliance or turning on a light, but it might be that there are other factors that have caused this problem. For instance, children playing with your machine can easily switch off both hot and cold water supplies at the same time.
If you dont have any lights on the dishwasher control panel, its worth checking that there is power to your machine. You can do this by plugging in another appliance and seeing if it works. If not, then consider contacting a plumber. It could be as simple as an issue with the main power source or the dishwashers wiring.
If this is not the issue, it could be that there are no lights on your machine because of a safety feature designed to stop children from using it without an adult present. Most machines have locks that prevent them from being used when they are in certain settings. This can also cause other problems if you want to use it for a different cycle or if the water supply is not hot enough.
If this does seem to be your problem, youll need to consult with your manual in order to reset the dishwasher properly so that you can start using it again. The machine should have come with one when you bought it, but do check online too because it might be available in a downloadable version.
Check The Child Safety Lock
Most dishwashers include a child lock feature to prevent kids from opening the appliance or changing the cycle settings. In many cases, the unit will not run while the child lock is engaged. Usually, the lock can be activated and deactivated by pressing and holding a button for three seconds, or something similar. If your dishwasher wont run and the door wont open, check the manufacturers instructions for the child safety lock.
Don’t Miss: What Is Automatic Dishwasher Detergent
How To Solve This
Locate the door latch assembly by removing the inner door panel. It should be at the top of the door. Then put the catch into the assembly to activate the latch switches.
You can also activate the switches mechanically by checking for continuity. If you test the switch terminals with the multimeter and the reading is zero, or near zero, its okay. If the reading is different, consider replacing the door latch assembly to have it work well.
However, if the problem is because you didnt close the door, do so. Open the door, then firmly close it to enable your GE dishwasher to run well.
Check Dishwasher Voltage Input

If a wall switch controls your dishwasher, check if its turned on. Then see if the machines cable plugs into the wall. Your outlet might be at fault, so test that, too. Finally, plug another device into the outlet and see if it turns on.
If the dishwasher plugs into a GFI or GFCI outlet, make sure the outlet is working, albeit in a slightly different way. These outlets have two buttons: Test and Reset. Press the reset button and see whether your dishwasher comes to life.
GFI and GFCI outlets regulate the amount of power an appliance receives to save people from electrical shocks. When these outlets sense an interruption in power, they stop the current before it reaches you. For example, if your electrical system is experiencing an overload, your GFCI outlet may have stopped sending power to your dishwasher.
If you havent found the problem, open the circuit breaker in your house and check if the circuit is off. You usually want the circuit closed to transmit electricity throughout your home. But modern circuit breakers are designed to have a fail-safe if the electrical current is too strong. They open the current with an automatic switch.
Lucky for us, circuit breakers can open and close without sustaining any damage. So turning on the circuit again by flipping the switch will not cause any harm.
- Dimmed or flickering lights
- Mild tingle or shock from electrical appliances
- Audible crackling and sizzling near outlets
Don’t Miss: Best Buy Dishwashers In Stock
There Is A Problem With The Trap And Filter Assembly System
Finally, there could also be an issue with the trap and filter assembly system. If the Trap inside the bottom of the dishwasher is clogged with debris, then the water pump may stop functioning. If the water pump is not working properly, the rest of the dishwasher is not going to function well either.
Before the rest of the dishwasher will start working again, you need to clean the trap and filter system. You need to take a look at the manual to see how you do this on your dishwasher. Once you clean the trap and filter system, the dishwasher should start working again.
These are just a few of the numerous reasons why your dishwasher buttons may not be working properly. Even though there are other possible reasons why your dishwasher buttons might be stuck, these are the most common examples. After you have figured out why your dishwasher buttons are not working, it is time to figure out how to fix the issue.
Do Not Hesitate To Call In A Professional
If youve done your best to bring back the lights to your control panel with no success, you should call in a professional. Go for experts that are known to repair your dishwasher model. If your dishwasher is still within its warranty period, you may be able to get your dealer to send a technician to your home.
Also Check: Best Dishwasher Detergent For Older Dishwashers
Get Your Dishwasher Buttons Unstuck
Ultimately, there are plenty of reasons why your dishwasher buttons may be stuck. Perhaps there is something wrong with the child lock, or maybe there is just a lot of dirt and debris built up.
Regardless, you may want to try a few of these solutions to get your buttons unstuck again. Make sure the buttons are clean and consider resetting the control panel. I hope you have enjoyed this detail guide. Take a look at some of the related articles below to learn more!
Home » Dishwashers » Are Your Dishwashers Buttons Not Working? Heres 5 Fixes To Try
Consider Using The Appliance Without The Lights
Its highly unlikely to find a newer model dishwasher working without the control panel lights on. If thats the case with yours, however, you can consider using the dishwasher with external lighting. Grab a flashlight, and you can use the appliance easily. This is a lesser hassle than going through the troubleshooting process, which can inadvertently lead to more serious damage.
Don’t Miss: Dawn Dishwashing Liquid 75 Oz
Control Lock Is Activated
Some models of dishwashers have a child lock feature that prevents children from opening the machine while it is operating. To deactivate Control Lock:
You need to press the LOCK pad twice within three seconds. When Control Lock is turned off, the lock icon will blink twice.
Youll need to refer to your product manual for this task, but you can also try to find it online.
Check Door Switch Operation
The door switch might be the culprit. Enter the error code mode on your machine by pressing the Cycle Select and Start buttons simultaneously for five seconds. This code will prompt the machine to do a Door Start Check.
If the door is closed properly, the lights will turn on. Flashing lights mean you should shut the door again. Make sure to press Start afterward to bypass the safety feature.
If the flashing lights remain, you might need to repair the latch or see if your dishwashers electronic control board is damaged. A working electronic control board is imperative because it regulates washing, draining, and drying cycles. As you can imagine, your machine is pretty useless without it.
Dishwasher doors might not latch if dishes protrude and are not organized correctly inside. Another potential issue is the surrounding cabinets preventing the door from closing, typically resulting from poor installation or loose screws.
In other cases, the latch itself is the problem. Closing the dishwasher door haphazardly might push the latch out of its position. If the door does close, but the latch fails to activate the lights, your latch will need to be replaced due to a mechanical or electrical malfunction.
In addition, door hinges may grow rusty or loose. If this is the problem, the door will move out of place when you push down upon it. The door may also look crooked and make a squeaking noise. Replace the hinges with new ones.
Don’t Miss: Frigidaire Gallery Dishwasher How To Start
Ge Profile Dishwasher Control Panel Replacement
If your machine is broken, it may be necessary to replace the entire control panel.
To replace the whole front panel and door, you will probably have to remove the old one!
You can find replacement control panels on Amazon and other stores that match your current dishwasher model number. Make sure your order fits the model you currently have.
Check The Dishwasher Power Cord

Some dishwashers have a power cord that plugs into an electrical outlet under the sink, while other dishwasher power cords are wired directly from the wall to the wires in the dishwashers junction box. If your dishwasher power cord plugs into an electrical outlet, make sure the power cord is plugged in.
If the power cord is plugged in, its possible the electrical outlet doesnt work. Check the electrical outlet for power by plugging in a small lamp. If it doesnt light up, have an electrician repair the bad outlet.
Heres a helpful troubleshooting video that shows this step and additional troubleshooting steps to take when your dishwasher has now power.
Recommended Reading: Are Yeti Lids Dishwasher Safe
Inspect The Door Latch
When the door latch is not engaged, a switch prevents the dishwasher from starting. Listen for the sound of the latch clicking into place when you close the door. With the door closed, pull on the door to see if it is closed securely. Visually inspect both sides of the latch for anything that may be preventing it from engaging properly, and for broken parts. If the latch is broken, the switch may be also.
Ge Dishwasher Won T Start Orange Light
Ge Dishwasher Won T Start Orange Light. The control panel should be cleared. The most common things that cause flashing lights include the door being left open, the latch on the door is broken or the dishwasher simply in need of resetting altogether.
No trouble finding others with my problem. I was having an issue where my dishwasher wouldnt start the start light would just blink and blink. I found a fix online where someone said lifting their.
Source: readytodiy.com
When starting your dishwasher first make. If the door doesnt close completely, something is blocking the.
Source: www.justanswer.com
It might be resolved by simply pressing the start/reset button. Open the door and press it closed again to see if the.
Source: expertappliancerepairorangecounty.com
Models with a delay hours button will allow you to start the dishwasher now The control panel should be cleared.
Source: dishwasherhelps.blogspot.com
Ge dishwasher wont start orange light. If your dishwasher isnt getting power, it wont be able to start.
Source: readytodiy.com
Once this is verified, locate the motor start relay next to. If the ge dishwasher seems to be having a power issue, like if you notice ge dishwasher not starting, no lights on the panel, or it.
Source: adiklight.co
Now, press both the start and the select cycle button down at the same time for five seconds. In this video we have a ge dishwasher model gdt655sgj0bb in which it was doing absolutely.
Source: readytodiy.com
You May Like: Can Caraway Pans Go In The Dishwasher