Dishwasher Leaking From Vent Cap
Some dishwashers have an external vent to expel water and warm air during drying. If the vent cap on the inside of the dishwashers door is loose, water can leak from the door during a wash cycle. To stop door leaks, check the GE dishwasher vent cap and tighten it by hand if its loose.
Is your GE dishwasher leaking water even after these troubleshooting tips? It may be time for a dishwasher repair service to assess the problem. Schedule your repair with Callahans Appliance today!
Problems With Lower Wash Arms
If there is a crack in the wash arm, water can spray up toward the bottom of the door. This will push water underneath the door and onto the floor causing leaks that could damage your home.
Unscrew the wash arm from its base and inspect it for cracks that could be causing leakage. Cracks can be sealed but not with glue since this will break down in dishwasher detergent over time.
If a new wash arm cannot be found then consider calling out a technician, as they have parts on hand to get your machine working again without wasting time driving around looking for parts and then doing all the work themselves.
Either way, if you are experiencing leakage at this point, make sure that your screws are tightened along with checking other possible causes such as motor mounts, pump housing or drains as these all play key roles in preventing water leaks when using dishwashers.
A Wash Arm Is Cracked
Most dishwashers have a top and bottom spray arm that sprays water through small holes during a wash cycle. If either arm becomes clogged or damaged, it can result in the dishwasher leaking through front door. Items that protrude from dishwasher racks and obstruct the spray arms rotation can also cause door leaks.
How do I fix a leaky dishwasher door if the spray arm is compromised? Try these tips:
- Wash spray arms regularly: Remove the spray arms and rinse them under running water to remove dirt and residue. Use a toothpick or straight pin to unclog spray arm holes before replacing.
- Load items properly: Dishwasher loading tips suggest placing tall plates and platters along the perimeter of the bottom rack so they dont block the spray arms. When loading, make sure items dont protrude from the top rack. Lastly, rotate the spray arms by hand before starting the dishwasher to make sure theyre not obstructed.
- Replace damaged parts: If a spray arm is cracked or permanently clogged it must be replaced to stop leaks and restore function.
Recommended Reading: How Long Should Dishwashers Last
What To Do If Leakage Persists
If the above-discussed solution didnât help you fix leakage in your GE dishwasher, then donât worry. There must be a technical problem inside your dishwasher.
In this case, I recommend you contact your seller or GE customer support. They will help you address or even fix the problem with your dishwasher.
In addition, if your warranty period is not over, you can repair your dishwasher free of cost.
Check the dishwasher warranty card that you got while buying your GE dishwasher. You can still call and talk about your problem if the warranty period is over.
Door Latch Is Damaged

One of the most common reasons your GE dishwasher leaks water from the bottom is a broken or damaged door latch.
This is the main reason the dishwasher starts leaking. Most of the time, this latch or gasket is damaged, due to which the dishwasher can start leaking.
Solution to this problem
You need to get this gasket or door latch repaired to solve this problem. If not repaired, try to replace it as soon as possible to avoid this problem.
To conclude, GE dishwashers are the most used kitchen appliance. They have numerous functions. Leaking the dishwasher can be disturbing as it can cause a huge amount of water under the dishwasher. Now, you can easily repair your dishwasher without professional help.
Related Guides
Recommended Reading: Garbage Disposal Dishwasher Drain Plug
Dishwasher Spray Arm Issue
Spray arm issues can also be responsible for a GE dishwasher leaking water.
The following spray arm problems can cause dishwasher leaks:
- Clogs: If one of the spray arm holes is clogged, water may be pushed out the remaining holes with excessive force that causes leaks. Detach the upper and lower spray arms and inspect them for clogs, removing any blockages with a straightened paper clip or toothpick. To prevent blockages, our dishwasher cleaning tips recommend repeating this process when cleaning other dishwasher components.
- Damage: Cracks or holes in the spray arm can also emit water with excessive force. Check the spray arms for damage and replace them if necessary.
- Loosening: If the spray arms arent clogged or damaged, make sure the screws in the spray arm support are tight. If the spray arm is loose, water can spray from the support, resulting in leaks. If any screws are loose, tighten them with a screwdriver to prevent leaking.
Wrong Soap Added To Dishwasher
If your dishwasher is leaking, it may be because dish soap was added instead of normal detergent. Use a detergent made for dishwashers to avoid this issue. If dish soap was already added, open the dishwasher and remove some of the soap. Check for any soap residue around the door seal and wipe it away with a damp cloth. Run the dishwasher on a normal run cycle to clean out the dish soap.
You May Like: Installing Air Gap For Dishwasher
Why Is My Dishwasher Leaking The Causes
Do you see water under the sink or below and under the dishwasher? Here are the possible causes:
- It has no seal.
This is a common cause if the leaking is happening through the door at the front of the appliance. If theres accumulated water underneath the door, then the door itself is the issue and the gasket is a likely culprit.
The gasket is made of rubber and is the go-to seal of virtually everything that requires sealing. Yes, including all dishwashers of all brands from Kenmore and LG to Whirlpool and Kitchenaid. In this case, its whats stopping the water from leaking out through the door. Needless to say, it will start to leak if the seal has been broken because of a missing or damaged gasket.
Fortunately, this is an easy fix. An experienced DIYer can simply replace the gasket with a new one.
- The latch is loose or damaged.
This is another thing to look at if the leaking is happening through the door. It could be because the door is not latching close properly. In this case, the latch is either loose or damaged.
- The pump is damaged.
The pump plays the important role of circulating water in your appliance. The pump of some brands is also responsible for draining the water. If its damaged or if its seal has been broken, then it can create a leak.
- Theres a hole in the tub.
Is the leak happening during the wash cycle? You may want to check the tub to see if there are holes. These tubs are susceptible to holes especially if theyve corroded already.
- Its overfilling.
Dishwasher Inner Door Causes Leak
If your dishwasher door seal gasket is NOT damaged, you may have loose screws on the door. The screws on the inner door may be loose and thus causing leakage. Use the proper screwdriver and tighten the screws hand tight. If you find that the screws are tight but one or two are missing, you can order new dishwasher screws and parts online.
Check dishwasher door for loose or missing screws
Here is a video to show you How to tighten loose screws on a leaky dishwasher
How to fix a leaking Dishwasher Door that has loose screws
Also Check: Bosch Dishwasher Door Falls Open
Dishwasher Air Gap Obstruction
Most dishwashers share a common drain with your sink or garbage disposal. To prevent dirty drain water from entering the dishwasher, some kitchens have an air gap next to the sink faucet. However, without regular cleanings, food particles and debris from the drain can build up and block the air gap. Dirty drain water will then back up into the dishwasher, causing leaks.
How do I stop my dishwasher from leaking when the air gap is clogged? Cleaning out the air gap should solve the problem. Remove the air gaps cover and manually remove any visible debris. Cleaning the air gap on a monthly basis, when you clean the dishwasher filter, should prevent clogs that cause leaks.
Fixing Other Leaky Components
Also Check: Whirlpool Gold Series Dishwasher Manual
Solution #: Replace The Door Gasket
Before assuming that the gasket is defective, check if it is dirty.
The gasket that seals your dishwasher becomes filthy as it withstands washing too many rounds of dishes.
Inspect the gasket and clean it with warm water and soap before you assume the more severe problem is to blame for the leak in your dishwasher.
Checking For Damages
A clear sign of a defective gasket is that the door wont shut properly even though the hinges are fine.
However, you must inspect it closely if the gasket has just begun to give away.
Look for any signs of cuts or tears in the gasket. The water might be leaking through any small hole in the gasket.
Does any of the above match what you are experiencing? Alright, it is time to replace the dishwashers gasket.
Replacing The Door Gasket
Open the dishwasher door and, starting at one end, pull the old gasket free of the channel.
Youre now ready to install the new door gasket.
The gasket is already installed, so ensure the door is closing properly. If it is, next, turn the dishwasher on to check if the issue has been solved.
Note: You might find the gasket also described as the seal. Sometimes they are different parts, but here they are the same.
Checking The Water Pump System

If your dishwasher is leaking underneath and no water is reaching the inside cabinet of the dishwasher, it is safe to say that there is a failure in the actual water pump. The water pump will need to be tested and then replaced.
If there is some water entering the dishwasher, but there is still water under the dishwasher you may need to visually check and possibly replace the hoses or clamps for the drain or water inlet. Look for cracks or loose parts in the hose or clamps on the ends of the hose.
Recommended Reading: Bosch Dishwasher E 15 Code
How Do You Replace The Bottom Seal On A Ge Dishwasher
To replace the bottom seal on a GE dishwasher, first, remove the upper rack by unscrewing the two screws on the front of the dishwasher. Then remove the lower rack by unscrewing the four screws on the rear of the dishwasher. Finally, remove the bottom seal by pressing down on one end and pulling it off of the dishwasher.
Ge Dishwasher Not Draining
Is your dishwasher completely empty, or is there always an inch of water in the bottom?
GE dishwasher not draining is likely to be caused by a clogged-up filter, blocked hose, or faulty pump.
Before you call a repair service, try these three simple fixes if your dishwasher wont drain.
Possible Solution:
- If filters are not cleaned regularly, they can become clogged. Locate and uninstall your filters.
- These are located at the bottom of the dishwasher, directly beneath the lower spray arm.
- To begin, twist the cylindrical filter to remove it from the dishwasher.
- Remove any gunk from the filters by gently cleaning them.
Blocked Drain Hose
- If cleaning your filters hasnt resolved the issue, a clogged drain hose is the next possible cause of your dishwasher not draining.
- The drain hose is an essential component of any dishwasher because it transports dirty water away from the unit. It is usually connected to the same drain as the kitchen sink.
- The drain hose could be clogged with grime and food debris or kinked, which is unlikely.
- To clean it, remove the drain hose from the dishwasher and the sink drain.
- The problem could also be coming from your kitchen sink. You can easily unclog a sink drain if you have a plunger or a drain snake
- Our drain service is available if you require additional assistance.
Blocked or Faulty Drain Pump
- A drain pump, like dishwasher filters, can become clogged by leftover food particles and grease buildup.
Don’t Miss: Rent To Own Portable Dishwasher
Dishwasher Door Gasket Causes Leak
The most common reason a dishwasher leaks water from the front door is the door seal . The door seal may have particles of food or broken glass on it near the bottom or sides and therefore cannot make a tight seal. Open the dishwasher door and check the dishwasher door gasket for any type of food, broken glass, or gunk buildup with baking soda and clean if necessary.
If you find the door gasket to be damaged, it will need to be replaced. Your dishwasher door seal gasket can be purchased online. Make sure you have the correct make and model number of your dishwasher when you order a new door seal gasket.
FYI: Some dishwashers have the door seal gasket mounted on the tub and some door seal gaskets are mounted on the door.
Dishwasher Door Seal Gasket
Here is a video to show you How to replace the door seal on your dishwasher
Dishwasher door seal gasket replacement
Solution #: Check Spray Arms
To check if the leak detected GE dishwasher is with the spray arms, start by taking out the bottom dish rack.
Next:
If they are broken or cracked, the water pressure may not be high enough to properly wash the dishes.
Furthermore, your dishwasher may leak if water is gushing out of the spray arms seams.
The spray tower should be raised as high as possible before being released. Such freedom of movement is necessary.
If you take off the top dish rack, you can reach the spray arm in the ceiling. Test the top spray arm the same way you tested the lower one.
The top spray arm may not sway as much as the lower one, so keep that in mind.
Note: If you notice any spray arms are no longer working correctly, it is time to replace them!
Replacing The Spray Arms
Once you have your hands in a new spray arm and the dishwasher opened up as instructed above, you must replace the part.
First, if you removed washers, reinstall them onto the spray arm in the reverse order you removed them.
To replace the spray arm:
Tip: The spray arms of a dishwasher may be detached for cleaning.
Soaking the spray arm in warm, soapy water is an effective way to clean it. Use a strong stream of water to make sure its clean.
Also Check: Frigidaire Dishwasher Is Not Draining
Leaking Dishwasher: Why Bottom Of The Door Fix Whirlpool Ge Kitchenaid
A dishwasher is one of the most important appliances we have at home. We dont really enjoy using it, but it beats the alternative which is to hand washing the dishes. Its safe to say that its hard to imagine living life without it.
Can you imagine having to deal with piles of plates and utensils after every family meal? Imagine having to wake up earlier than the usual just because you have to set aside time to wash the dishes before taking your kids to school and going to work. Imagine having to sleep later than usual just because of the piles of dishes that you wouldnt want to leave unwashed for the night.
It takes a lot of precious time and effort. Instead of resting or spending quality time with the family, youre stuck with hand washing the dishes. The repetitiveness of it all will really test your sanity. Lets face it. No one wants to wash the dishes. Your trusty dishwasher somehow makes the task tolerable.
Things change when it starts to leak. Its not supposed to leak. A leaking dishwasher is not an effective dishwasher and is potentially an unsafe one. Most homeowners are at a loss when this happens. They dont know what to do. A lot of them end up buying a new one.
Doing so may help in the short term, but it can be a wasteful investment. You can still fix it. Weve put together a step by step guide on how to fix a leaking dishwasher. It may just save you a lot of money from having to buy a new one.