Door Seal For Kitchenaid Dishwasher

Damaged Latch Or Gasket

A damaged latch or gasket is another KitchenAid dishwasher leaking cause. KitchenAid dishwashers can leak from the door seal if it warps, breaks, or becomes brittle due to age. The seal may also be damaged by too much heat and repeated use and cleaning cycles that create a buildup of detergent on the rubber surface.

If the water is accumulating directly underneath your dishwasher, you likely have a leaking door. Check for any cracks in the door or loose latches that may be causing the leak. To fix the leak, tighten the latch on the door. If that does not work, there may be an issue with the gasket, and it will need to be replaced. This is the rubber seal around the door of your dishwasher. If its damaged, you can replace this easily.

W10300924 Dishwasher Gasket By Blue Stars

Perfect Fit, High Quality & Easy To Install

The W10300924 Gasket is for dishwashers. Gasket seals the gap between the opening to the dishwasher tub and the outer edge of the door. After installing the gasket, shut the dishwasher door and leave the door closed for several hours to properly seat the new gasket.

Fixes the following symptoms

• Made of high quality materials
• Wide compatibility with OEM specifications
• No harmful chemicals and safe to use
• Long-lasting

About BlueStars

At BlueStars, we dedicate to making your life uncomplicated, comfortable, and convenient with economical DIY repair solutions for your appliances.

Reliability is what we aim for. We offer you not only high-quality products but also great 24/7 customer services that ensure your satisfaction.

Reasons Why Kitchenaid Dishwasher Is Leaking

Eugene SmithDISCLOSURE: This post may contain affiliate links, meaning when you click the links and make a purchase, we receive a commission at no additional cost to you

Kitchenaid dishwashers use water to clean the dirty dishes that you load inside. Typically, these dishwashers have no problems keeping all of the water and suds contained inside the appliance. So, why would a Kitchenaid dishwasher be leaking onto your kitchen floor?

The most likely reason for a Kitchenaid dishwasher to leak is a faulty water inlet valve. Water could be leaking from the valve itself, or it might be stuck in the open position causing an overflow inside. Damaged seals or gaskets on the diverter motor or around the door could also let water through. The same could also happen from the drain pump or its hose.

Lets take a closer look at the possible reasons your Kitchenaid dishwasher is leaking, and what you can do to fix it.

Don’t Miss: Dawn Dishwashing Liquid 75 Oz

Remove The Old Gasket And Clean The Channel

Grasp one end of the gasket with your fingers or a pair of needle-nose pliers. Remove the old gasket by pulling it out of the recessed channel. Fix.com recommends pushing down on the gasket at the bottom, as this will release the gasket. Pay attention to the orientation of the gasket as you remove it so that you can install the new gasket with the correct side out. Clean the channel and dishwasher door with a paper towel or soft rag. Be sure there is no debris remaining in the channel.

Press The New Gasket Into The Channel

Hold the new gasket in the middle so that an equal amount hangs down on either side, instructs Sears PartsDirect. Use your fingers to press the center of the gasket into the channel, starting at the top center of the dishwasher. Continue pressing the gasket into the channel across the top and then down one side of the dishwasher tub. Press the other side of the gasket into the channel in the same manner.

Also Check: What Does Ih Mean On Ge Dishwasher

Damaged Door Gasket Or Seal

As a general rule of thumb, any appliance that involves the use of water will have a number of gaskets or seals around several of its components. Your Kitchenaid dishwasher is the same, and one of the most important seals on it is the one around the door.

This seal is crucial because it prevents water from leaking out from the doors sides whenever youre running a dishwashing cycle.

Sometimes referred to as a gasket, this part forms a tight seal whenever you shut the dishwasher door. It not only prevents water but also stops suds and food bits from coming through the door.

Is The Dishwasher Level

Make sure the dishwasher is level. The dishwasher must be supported by the leveling legs and rear wheels and must be flat on the floor.

NOTE: Some models will have four leveling legs.The dishwasher must also be square in the cabinet. If the tub opening is not square, the door will not seal properly. This is the responsibility of the customer or installer.

to watch a video on how to level your dishwasher.

Also Check: Ge Dishwasher Wont Turn On

Faulty Water Inlet Valve

Your dishwasher gets water from your main line through the water inlet valve. To determine if there is a leak from the underneath of the machine, remove the bottom kick plate at the back, hot water comes in through one of three tubing systems: rubber hose , copper tube , or braided material .

Look for the supply line and trace it to the valve inlet to check that it is tight with no leaks or cracks. Look for symptoms of trouble on the rubber or plastic outlet hose coming back out of the valve. Be sure to also check the plastic of the water inlet valve and the injector on the side of the tub. To check for dishwasher leaks, leave the lower kickplate off and watch the washing cycle.

If your dishwasher continues to fill above the heating element after lowering the float switch and opening the door latch, there may be a problem with your inlet valve.

Using The Wrong Detergent

Are you using dishwasher detergent or sink soap? Be sure to use the right type of detergent in your washer. Dishwasher soaps are created for dishes without creating bubbles that cause an overflow, and if theyre not working well enough, maybe its time for a change. Using too harsh types of cleaners can also lead to cracking and erosion on the bottom floor inside your dishwasher tub.

Some dishwasher detergent/soap will cause too much sudsing, making a mess around the door and may leak out past the door. To solve this problem, change your detergent to one made specifically for use in the dishwasher.

Also Check: Whirlpool Dishwasher Top Rack Clips

Are There Items Between The Door Seal And The Tub Of The Dishwasher

Check that there are no items such as silverware stuck between the door seal on the dishwasher door and the tub of the dishwasher. This will cause the door to not shut or seal properly.

Check both racks for items that may be stuck and protruding. Remove any item that is protruding outside the rack.

Check for large food particles around the door seal. Large items could cause the door to not shut or seal properly.

Replace The Dishwasher’s Lower Rack

Place the lower rack back into the dishwasher. Close the door and lock it. Leave the door closed and locked for at least three hours to give the new gasket time to conform to the door. Run the dishwasher and check for leaks.

Things You Will Need

Tip

If the new gasket feels hard or dry, soaking it for a few minutes in a sink full of hot water will soften it and make it easier to fit into place. Another option is to blow warm air on the gasket using the low heat setting on your hair dryer.

Most dishwashers have a lower seal as well, which is generally a much more involved job requiring removal of the door. Make it a point to periodically clean the surface of the door where the gasket seals. Sticking, torn gaskets are the cause of most door seal leaks.

References

Read Also: Whirlpool Dishwasher Heating Element Replacement

Stuck Or Clogged Spray Arm

As water is forced through the dishwasher spray arms, it sprays and covers the dishes in detergent. All dishwashers have a lower arm that is located at the bottom of the dishwasher, and some models also have middle or upper arms below the top rack on top of the tub.

The pressure of the water being sprayed can cause damage to the plastic spray arm or metal head which alters its ability to disperse water evenly. This can result in a leaky dishwasher door at the bottom where theres no sealant for protection from incidental contact with water. Replace the broken spray arm to solve the KitchenAid Dishwasher Leaking problem.

Connect With An Appliance Repair Tech

No in-home service calls. No appointments.

• Next, remove the toe panel and locate the water inlet valve.
• Prepare a towel to catch any spills as you disconnect the valves electrical and water connectors.
• Depending on the design of your dishwasher, you might need to unthread screws holding the valve in place.
• Next, install the new water inlet valve the same way as the old one. Reconnect the water and electrical supply to the valve, and mount it back in place.

Also Check: Maytag Jetclean Dishwasher Eq Plus

Ultra Durable W10300924 Dishwasher Gasket Replacement Part By Blue Stars

• ð ððð% ðððððððð ðððððððð: Customer satisfaction is our priority. If for any reason you’re not completely satisfied, you can ask for a replacement or FULL refund, no questions asked. Buy with confidence!
• MODEL NUMBER: W10300924 Dishwasher Gasket.
• EASY TO INSTALL: It is made exactly fit for most top name brands , and replaces part numbers: W10300924V, W10300924VP, PS11722167, AP5983731, EAP11722167, 4258949, PD00023975.
• FIT MODELS: – 66512776K311, 66512782K311, 66512833K311, 66513222N410, 66513222N411, 66513222N412, 66513253K110, 66513259K111, 66513933K010, etc. – 7WDT790SAYM2, 7WDT950SAYM1, BLB14DRANA1, BLB14DRANA4, IUD7500BS1, IUD7555DS2, etc. – KDFE104DSS0, KDFE104DSS1, KDFE104DSS4, KDFE104DWH4, KDFE204EBL3, KDFE204ESS1, etc.
• PREMIUM QUALITY: The replacement part is made from durable high-quality material and well-tested by the manufacturer – Meets OEM standards – Ensure long-lasting and effective performance. If you notice that your dishwasher is leaking, the gasket is a good place to start diagnosing the problem. If the gasket is loose or damaged, it may need to be replaced.

How To Replace A Dishwasher Door Gasket

Related Articles

• How to Fix a Vessel Sink That Doesn’t Drain

A puddle under the dishwasher is doubly distressing. As if the thought of a potentially expensive repair isn’t bad enough, there are all those dirty dishes that might have to be done by hand in the meantime. If you’ve managed to track the leak down to the door gasket, believe it or not it’s your lucky day. The part is fairly inexpensive, and replacing a dishwasher upper door gasket is among the simplest of home appliance repairs.

Also Check: Samsung Dishwasher Heavy Light Blinking

How Do I Change The Door Seal On My Kitchenaid Dishwasher

4/5complete answer

Clean the rubber seal of your dishwasher with a solution of three cups hot water to half a cup of vinegar or bleach. This is important because the seal can catch food or get moldy. Clean the under-edge of the door with the same solution.

Similarly, how do you replace the door seal on a Whirlpool dishwasher? How to Replace the Front Door Seal on a Whirlpool Dishwasher

Thereof, why is my Kitchenaid dishwasher leaking?

If the wash arm support is loose, water can spray out between the wash arm support and the lower pump housing, causing waves. These waves can cause water to leak out of the bottom of the door. If the upper wash arm is cracked, it can force water to spray directly toward the dishwasher door seal, causing a leak.

Why is my Samsung dishwasher leaking?

If the wash arm support is loose, water can spray out between the wash arm support and the lower pump housing, causing waves. These waves can cause water to leak out of the bottom of the door. If the upper wash arm is cracked, it can force water to spray directly toward the dishwasher door seal, causing a leak.

Check Hose Clamps & Hoses

Often, the hoses and clamps on KitchenAid dishwashers will need to be tightened. KitchenAid dishwasher connections are prone to leakage due to this problem. The connection at the top of your Kitchen Aid lower arm may also leak if it is not connected securely enough in its tube connector below the waterline.

If the dishwasher has come loose or has cracks in the hoses, it could be the cause of a leak. Check both clamps on the drain hose and the circulating hose.

We hope that now you are not facing the KitchenAid Dishwasher leaking problem. Please do comment with your questions, and we will be happy to answer them.

Don’t Miss: My Dishwasher Smells Like Fish

An Ideal Repair Solution Buy

BlueStarsâ replacement parts are manufactured of high-quality and durable materials free from harmful chemicals. By doing numerously strict tests and reviews performed by our experienced engineers and development team, we commit all products to meet OEM standards and are safe to use.

We also support customers with a coverage on all products and 24/7 customer services which ensure you have a happy shopping experience. All is for us to build a relationship of confidence that you can count on.

3.8 out of 5 stars

How It Fails:

If you notice your Kitchenaid dishwasher leaking, particularly from underneath, then the most common reason is that the water inlet valve is faulty. Thats because the valve is located on the bottom of the appliance, hidden behind the toe panel .

When this happens, water will leak out from the inlet valve itself and flow directly onto the floor underneath.

Alternatively, a faulty water inlet valve can also be stuck in the open position. That will cause far too much water to flow into the dishwasher, causing water to leak from around the door.

Read Also: Dishwashers On Sale Stainless Steel

How To Fix:

To fix this, youll need to replace the diverter motor seal with a new one. Then, youll be able to access that seal from inside the dishwasher.

• First, though, youll have to remove the diverter tube assembly that sends water to the various spray arms.
• Once youve taken that out, you can twist open the diverter cap and see the seal that youre looking for.
• The seal will be wrapped around a white plastic stem.
• Remove the old seal and replace it with the new one. The seal has a flat side and an open side. The flat part is meant to face down when you push the seal into place.
• Lastly, reassemble the diverter tube assembly.